Search results

Swapped in the Corteco, and Im leak free now. Took all of an hour.

following. I dream of a either a 300, 4BTS (rovingbeetle) or 2.8 Cummings swap in my 00DII. Good luck OP, and thanks for sharing.

This is cool, thanks OP for the heads up.

Just found this reference from another (firearm) site, thought I'd pass it along. Enjoy. https://www.auveco.com/land-rover

Late to the conversation, but I also just completed the oil pump/timing chain/front cover gasket task stemming from a front cover gasket leak, and like the OP, the cheap ass Britpart/Allmakes front cover seal is leaking like a sieve. thanks to the other posters for both the Corteco and sleeve...

I'm scavenging parts from a D2, and want to keep the transmission as a future spare. Its strong, and only has 160 I currently have the motor torn down to the block. I've got both an engine lift, and a transmission jack/lift. Whats your opinion on the following actions that would most likely...

Sold Pending Meet: Available. $600 Safety Devices LOW "Low Lander" Roof Rack for Land Rover Discovery 2. You must remove your factory roof rails-easy to do, plenty of how to online, Youtube. Rack is in good condition, light surface rust, and two areas where the rail is slightly bent. Only...

After two head gaskets, cyl no. 5 is flooded with coolant. With the head off, I'm not seeing a crack, or a point of ingress. 1. Any clues on what/where to look? I've got a machinist bar, but haven't checked flatness yet I may be able to get my hands on a 4.6 block from wrecked 04, and...

I just redid head gaskets on my D2 where I used ARP studs the last time, and yes, I pulled the three, top, long studs to get them out of the way, and be able to lower the head back on the block easily. Funny thing is I got the heads off WITHOUT having to remove those longer studs. Once I got...

NTC9416 is what I ordered from AB. Regardless, I got it to work, and am happy for now.

because we want to buy land for our very own Land Rover Driving Experience, then hang around afterward talking about our leaking trucks.

Yes, my bench is trashed at the moment. The only trick I used was to cut off a 1/4" from the bottom bolt of the passenger side transfer case mount. Even with the transfer case jacked up as far as possible, and the mount base removed/loosened from the transfer case, It barely fit while...

Pic of the drivers side with the new, modified D1 mount installed. I have since tightened that bolt.

I picked up a used 'Porta Power'/hydraulic ram, whatever you call it, off FB market place last year for another project. I used it to push back the motor. Made it effortless. Most rental companies have these available. You could use a bottle jack and 2x4 to do the same. I left the drive...

This pic show how far forward the motor was. The motor was essentially 'resting' on broken mounts. Good thing I drive like the old man I am.

Here's the problem I ran into. thought I had a pic, but my drawing will have to do. Could be my fault ordering the wrong mount. I used D1 300 TDI mounts. There was a gap between the mounts bottom resting surface given the frame mount lip. I removed about an 1/8" plus to of materiel from...

One of those is the drivers side mount that I replace 9-10 years ago. The drivers side transfer case mount was still intact, but on its way out.

The package does not. Scam like ain’t it ?!?!? They’re trying to take advantage of us Rover V8 folks trying to keep these old trucks running! As a side note, anybody here ever used these Felpro's??

Well Hell, my googlefu sucks! appreciate ya'll educating this amateur, shade tree Rover mechanic. Reading in another thread, it sounded like 'MLS was some new, miracle gasket. I had an Elring fail at 55k ish. Ive got the BritPart gaskets handy, they're about to go in so I can get back on...

Let me add, that until recently, I had never heard of "MLS gaskets". My search for info on MLS led me to these Felpro's. I ordered a set, and yes, they're essentially composite on thin metal such as the Lucky8 supplied, or Elrings. The noticeable difference is the you'll see the Felpro has...