Search results

  1. Mike26

    Series Trek still exist?

    Does anyone know if Series Trek still exists? I’m interested in their 24 spline HD shafts so that I can look into installing an ARB in a ‘72 Lightweight. http://www.seriestrek.com/axles.html
  2. Mike26

    D2 CDL Light not engaging after new tranfercase

    I have now replaced my '01 CDL transfercase with a freshly resealed '04 transfercase. The '04 transfercase has two CDL sensors in the front output of the case, as opposed to the one sensor that my '01 had. I cut and crimped the old wires and attached them to the front most sensor on the '04...
  3. Mike26

    ANR1534 wheel

    Come to find out my Lightweight came with 4 of these under it, but I'm hoping to find a 5th to use as the spare. By chance does anyone have an extra laying around? Looking for a spare. Searching has found these were used under the one ton series 109's, defender 130's and NAS 110's.
  4. Mike26

    7.50 x 16 Michelin XZL

    Anyone by chance have any XZL's in good shape for sale?
  5. Mike26

    P38 HEVAC Display

    Looking for a clean working HEVAC display for a P38. Not sure if it makes any difference but its a 2001 4.6 SE. Mines shot, button faded and LCD screen isn't cutting it.
  6. Mike26

    D2 offset radius arms

    Sold
  7. Mike26

    Transfer case front output vibration

    The front output shaft/flange on my 01 D2 has been vibrating for a couple years now. Until recently, it was live able. I've replaced both the flange and front output bearing, but have never been able to reduce the rotational wobble. It can be moved up and down a fair amount just by hand and...
  8. Mike26

    2001 Land Rover Discovery II

    Trucky :: 2001 Land Rover Discovery II (2015-07-02 18:35:59)
  9. Mike26

    4.6 piston and connecting rod

    I am in need of a 4.6 piston and connecting rod. Purchased a 4.6 block (for the rotating assembly only) out of a 04 D2 that was missing one piston and one connecting rod. Needing these parts to begin the next engine build
  10. Mike26

    Timing chain play

    In the finishing stages of building up a 4.6 with crower 229 cam. Ordered all new timing chain, cam gear and crank gear. After the gears and timing chain were installed and the top end of the motor all put together we were rotating the block and noticed that the entire timing chain is tight...
  11. Mike26

    camshaft bearing wear

    about to put this 4.6 block all together later this week. Block, heads, crankshaft and all the bits were taking to the machine shop and cleaned up and gone through but we didn't replace the camshaft bearings. Camshaft is going to be replaced with the Crower 53229. The engine is out of a 2003 D2...
  12. Mike26

    rough idle upon start up

    In the past 2 weeks, about every time I start up the D2 it will fire right up, idle at about 1100-1200 RPM for about 5-10 seconds and then start slowly decreasing the RPM until it arrives at its normal 650 RMP level but once it reaches 650 RPM the engine will begin to run rough and shake the...
  13. Mike26

    Honda Civic question

    I just took into my possession a free 2001 civic lx 4 door with a bad transmission in it. Car has 134,000 miles and the auto transmission just took a dump in it last weekend. It was my girlfriends car and she bought a new Hyundai and said I could just have the civic. Car is in great condition...
  14. Mike26

    D2 drive shaft

    Stock front drive shaft from my D2. Had 2 greaseable u-joints replaced in the double cardon joint at about 60K. Took the drive shaft out at 70K and replaced with a tom-woods. It has been sitting on my garage floor since I took it out. Works just fine, close to died red from the east Texas dirt...
  15. Mike26

    Opinions on a good AR15?

    I am looking to buy an AR15 in the next few weeks and I was looking for some input on what to look for. I was looking at the S&W M&P 15. Found a new one for $840 shipped online. Are these decent enough to taking to the range every month and for the coming zombie apocalypse?
  16. Mike26

    New Fan clutch, junk out of the box?

    I ordered a new Hayden fan clutch (part number 2991) from summit and just got it today. Installed it, and noticed that when I turn the truck off (after it is at operating temp) the fan will free wheel for a good 10 seconds. Am I mistaken, or is this is a bad fan clutch? Shouldn't the fan stop...
  17. Mike26

    D2 running warm

    Ok, I have searched and read quite a few older posts about the D2 motors running warm, but I was hoping I could get some exact answers in my case. Earlier this week mine decided to begin doing this as well. At idle after warming up the aux fans will kick on and stay on until the truck moves...
  18. Mike26

    Template for snorkel

    Would anyone happen to have a template for installing a safari snorkel on a D2?
  19. Mike26

    D2 SD Rack

    Looking for a safety devices roof rack for a D2 within 300-400 miles of Dallas TX. Let me know, Thanks. -Mike Neal
  20. Mike26

    Disco 2 Receiver Hitch

    Recently installed a Greg Davis rear bumper, so the OEM receiver hitch is up for sale. Includes all hardware EXCEPT the two bolts that go into the crossmember. Looking for 100 plus shipping. Located in Plano TX