Search results

My new Rover does not have Rover any drive train. Everything is for sale except the winch. If you need it or want it I probably have it. Everything is in Vermont, I am willing to ship on your dime. I can help with RURR or will travel for the right price. SafariGard bumper Homemade Sliders, skid...

ARB D2 steel winch front bumper. Rusty but complete with turn signals and crush cans. I can repair and repaint for additional cost. I can help with transport within Vermont. I can send pictures. Will trade towards LS engine. Dan

I can fix your bent trailing arms. $150 plus freight. Compared to TerraFirma which are 3/16 .188" wall and over 200$ I use your factory trailing arms ends and sleeve with 1/4" wall DOM tubing. They can be bent or straight trailing arms. I have a tube bender if you would like a specific degree...

All located in VT, I do have access to a Fastenal store. Willing to use RURR if possible. D1 cranked trailing arms: SOLD pair of D1 or D2 clamp on diff guards, used good shape. SOLD TerraFirma front D2 diff guard. Used needs paint. 50$ plus shipping Homemade D1 front diff guard, all 1/4"...

Does anyone have a pictures of the 3rd mounting bolt in the mounting brackets? Mine keeps rotating up and smashing the headlight finisher. It has moved enough to dent the leading edge of the front fender. Thanks, Dan

If I am looking for an LR3, what should I be looking for? V8, V6, HD, HSE, any years better than the others? Jag or BMW engine? Ideally I think I want a V8 Hd with the locking rear diff. This would not be a deal breaker if a cheap clean one showed up. Thanks, Dan

Hello everyone I am parting out a 1995 D1 SE7, I bought it last weekend. Originally Roman Bronze, now spray painted red. 3.9 147k miles that runs decent, oil cooler leaks badly. No idea if head gaskets have ever been done. Interior is decent, manual leather seats have seen better days. Jumpseat...

I drove my D1 to work today and home with no issues. About 15 minutes after getting home I try to take the dogs out for a run and swim., Disco wont start. Just relays clicking under the dash, I don't hear the starter solenoid making any noise. I transfer dogs to my truck and go on about my...

I need a RH (pass side) headlight finisher. Any color is acceptable. Shipped to 05482. Thank you, Dan

WTB D1 NAS pass side headlight finisher and grill. Any color as long as it is not broken. shipping to 05482. thank you, Dan

see title. Mine leaks really badly. I have to pull it but the vehicle has no engine in it. So access is pretty good.

If you are getting water in the headliner this may be a simple temporary way to minimize the leak. I have no headliner so I have noticed that when I park facing uphill in the rain the drip pans fill up and then overflow in the back when I drive off. If I park facing downhill the drip pans drain...

Need 2 more to make a whole set. Shipping to 05482. Thanks, Dan

Sterling 10.25/10.5 long spline 1350 yoke needed. shipped to 05482. I know it is a long shot, but you never know until you ask.

I am looking for an empty front axle housing shipped to 05482. Cheaper is better for sure. I need it for mock up of new front suspension. Perfect is not required, but useable would be nice when I am done. May be a shameless SG 3 link copy or a different 3 or 4 link depending on packaging room...

Driving home from the trail my disco wont Rev and is very slow. Backfiring under the hood when under load, easing out of the throttle seems to make it better. I will check fuel pressure tomorrow. I am thinking either VSS or CPKS, am I on the right track? thanks, Dan

Looking for a front D1 driveshaft to cut apart and lengthen into a rear shaft for a project. Cheaper would be better for sure. Shipping to 05482. Thanks, Dan

What is acceptable driveline slop? With my digital protractor I get these rotational measurements: Front diff yoke no driveshaft attached 16 degrees Rear diff yoke with drivehaft 6 degrees Rear T-case output is the same 6 degrees as above, the driveshaft is still attached Front T-case output...

It wasn't exactly the mall or even on pavement. But it did break and leave me stranded for a bit. It made some bad crunchy noises and then it was like driving with all the brakes dragging. All the gear teeth are in the bottom of the case and it seems like every gear and shaft has broken teeth. I...

How much would a replacement engine cost? I would also need shipping to 05482 if you have one for sale. I do have access to a business address with a loading dock for truck freight. Contemplating buying a D2 with a bad lower end knock. Just trying to see if the numbers add up, I will do the...