Search results

  1. parsonsjunior

    7100 rebuild

    So, I've nearly completed repairing and revalving a set of 7100. All about the job is pretty straight forward, I just followed the directions that are out there. My question is; is there a sequence to filling the oil and replacing the piston? As in, should I replace some the oil before...
  2. parsonsjunior

    7100 revalve

    I have been trying to speak to someone a bilstein for over a week. All I need are the part numbers for the valve plates so that I can build a 400/100 valve stack. I have the Pdf w/ all the part numbers but, I have no formula to make those numbers work. Any advise or help will be appreciated. Sam
  3. parsonsjunior

    A few things

    Looking for g4 rear upper light guards, Bilstein or OME steering damper for DII, and still searching for the KM1 285/75 16. Still looking for used cranked radius arms for DII, also used TW or GBR front double or multiple double Dshaft. Shipped to 30005. Thanks Sam
  4. parsonsjunior

    Pissing into the wind?

    Unmolested unicorn. That's what I want. But what I need is 1 285/75 16 BFG KM1 at least 75% of tread left and if at all possible mounted on a 16X7 AB style steel wheel. I just bought 5 brand new been setting in a guys shed since 2007 no dry rot, perfect. I already found 5 so I know there's one...
  5. parsonsjunior

    Dii radius arms

    Looking for a pair of DII cranked radius arms. I've got about 4"s of lift on my 99 and my ride and steering have become melancholy.
  6. parsonsjunior

    Another F'n tire question?

    Does anyone have experience with Firestone Destination MT?
  7. parsonsjunior

    CDL Quickie

    I've got a tab for the CDL switch. I'm going to just bolt it on so I can do a reach around and engage my diffs. I must have tried a dozen nuts and nothing wants to tighten up. So, does anyone know exactly what it takes and if it's fine or wide thread pattern? Thanks
  8. parsonsjunior

    Bushings

    I need some sort of step down bushing or just a poly spacer. I installed RTE towers and shock mounts and the bilstein i chose is rattling around in them. Surely there's and easy fix I just haven't found it yet.
  9. parsonsjunior

    spacers

    I need a pair of 1" coil spacers for the rear of a DII. I'm in 30005 if you have a pair quote me price shipped. Thanks All
  10. parsonsjunior

    used MTs

    255/85 265/75 285/75 305/70 for 16" alloys really want MTs but would entertain ATs need something to get me through to Aug. so they don't have to be too impressive and the cheaper the better also the closer to Ga. the better
  11. parsonsjunior

    Bilstein Lenghts

    I'm about to install the 3" RTE springs in my 99 DII. I'm also planning to install 12" travel Bilsteins. Is that the wrong choice in the shock? Will a larger bump stop solve the issue? Different shock towers? Or will they be fine? I don't want to to be slamming these shocks. What is the total...
  12. parsonsjunior

    DII Tubular Shock Towers

    Just looking for a set the tubular towers for my DII. I haven't seen any U.S. suppliers so I'm hoping someone has a used set lying around.
  13. parsonsjunior

    used springs

    I'm looking for a set of 3 or 5 inch rte springs. Or just a set of 3" rears HD.
  14. parsonsjunior

    Berryman's B-12 Chemtool

    I know some of you have used chemtool in your fuel tanks. Has anyone added Berryman's to the crankcase or transmission? I was also planning on adding it to diffs; right before I drain them all, of course. Is any of this advisable?