Search results

  1. boxster

    Plip programming

    Anyone know who in forum does Plip programming 97 D1 2 button remote?
  2. boxster

    97 D1 Turn signal repeater lamp

    How does this lamp attach to the fender? Appears the gasket and clip is missing. Any ideas are appreciated.
  3. boxster

    WTB LYNX EVO2

    Anyone state side tried this scan tool?
  4. boxster

    ELM 327 interface

    Installed the gems ECU utility for Land Rover, turn key to position 2, paired the app with dongle, however when you select connect to ECU app does not connect? Anyone with ideas on what to do?
  5. boxster

    97 D1 speedometer problem

    Speedometer won’t register past 60mph at speed. Then when at stop it’s at 10mph. What’s could be the problem? Any thoughts appreciated.
  6. boxster

    4.0 Engine tapping noise

    97 D1 4.0 engine tapping noise when warm? Suspect rocker arms wear. However I engaged the A/C Compressor and tapping sound became louder. Disengage sound is less noisy. Any ideas appreciated.
  7. boxster

    4.0 engine noise?

    Hearing a tapping noise when idling and warm engine appears it’s on drivers side. Could it be lifter or rocker arm? Any ideas appreciated.
  8. boxster

    97 D1 key fob program

    Anyone know of programming sequence for D1. Replaced original ECU with used ECU with matching alarm due to acceleration/power problem. However the handset or remote not working to lock/unlock vehicle. Any ideas appreciated.
  9. boxster

    97 D1 key fob stopped working

    Changed ECU wIth matching alarm. Now key fob not working? Is there a reset sequence?
  10. boxster

    97 D1 no acceleration with maf connected.

    D1’s been down for 2 weeks, between myself and the mechanic shop no resolve. Tried 3 different mafs 1 new and 2 known good mafs from running D1’s. The codes point to the maf but obviously not it. New fuel pump, pressure correct, etc. Unplugged maf goes to pre set values and runs right. From...
  11. boxster

    97 D1 alternator output

    Can a faulty alternator output current interfere with signal to ECM trying to communicate with MAF? My tech says Maf is not problem. Any ideas?
  12. boxster

    97 D1 runs great with MAF unplugged?

    First wouldn’t run or idle or accelerate. Now it idles correctly and has great acceleration! I know it can’t run this way. Going to find another MAF that works. Anyone with other ideas?
  13. boxster

    97 D1 won’t accelerate

    D1 starts but won’t gain speed, had this happen 4 years ago was failed fuel pump. Recently replaced fuel filter and fuel pump, changed spark plugs, replaced damaged CKPS connector all with no resolve and no CEL. MAF sensor replaced 4 years ago so next I replaced MAF with known working MAF no...
  14. boxster

    D1 won’t accelerate

    By the way I’m going to get the fuel pressure tested. I believe it’s 36 psi at run and holds for ten minutes after shut down. Again the pump is new. Just thinking that fuel regulator has failed? Any thoughts appreciated.
  15. boxster

    97 D1 rough idle

    Ok repaired crank sensor wiring still rough idle, no acceleration? In the beginning ran but no acceleration, suspected fuel delivery problem so went with fuel filter and fuel pump no change. Next suspect MAF cleaned it installed no change, replaced spark plugs no change, last repair is crank...
  16. boxster

    97 D1 CKPS CONNECTOR

    Anyone know where to buy new connector?
  17. boxster

    97 D1 lost power won’t accelerate

    Changed out fuel filter no difference, fuel pump, still runs rough. Changed out spark plugs no resolve. Cleaned out MAF no difference all the time no CEL? Bought a known working MAF installed and would not start. Unplugged the MAF started right up. Installed original MAF started right up however...
  18. boxster

    Code P0183

    Every time I Gas up my 97 D1 4.0 with 310K miles the code P0183 appears? I erase code and it doesn?t show up until next fill up which is twice a month any ideas appreciated. Boxster
  19. boxster

    97 D1 blower fan

    My fan speed control works on all speeds however I thought speeds 1-3 are resistor controlled and speed 4 or hi was on its own circuit with fuse and relay control? My blower fan isn?t blasting air on hi like it should. I see several posts about remove unit and clean out. Is there another fix...
  20. boxster

    97 D1 Blower fan motor

    My problem is when the fan control is on position 4 it doesn?t have max air flow. HVAC works on all speeds just seems at position 4 not enough air flow. Is the fan motor failing or is there a relay somewhere that?s failed? Any thoughts are appreciated! Thanks