Search results

These are a direct bolt-on. The tpms sensors (315khz) were swapped over from the factory alloys. I like the look and access to more tire options.

Referencing a later V8, I’m going through the timing cover/oil pump assembly. There is one pressure relief spring (bottom right facing the engine) that’s a no-brainer. It recirculates oil around the pump if pressure exceeds the factory spring. On the left hand side is another spring that by all...

Are 2015 LR4 front seats a direct replacement in a 2013 LR4?

I’m looking for the part number of this hose and tube assembly. It is V’d at both ends. The water pump end has that 90 degree connector that pushes into the water pump housing and the other to the outlet for throttle body heating. The other end goes to the reservoir and the radiator through...

Anyone know this truck? It’s a long drive to be disappointed. 1999 D1 SD (with sunroofs sadly). Looking for a project for my grandkid but don’t want a heap.

I’m intent on removing the SAI on my 02 D2. A non-SAI truck was stripped on the engine harness, fuel pump harness, fuel pump, vent canister assembly, gauge cluster, bcu and ecu. Swapping all of these in are no issue. What had me questioning the conversion is the the difference in wiring. The...

I changed the oil in my '13 LR4 using a new filter and 8 liters of oil. After running it at idle then letting it sit shut down for 10 or more minutes the service menu shows the oil level to be minimum. What gives?

I wanted to add the ladder to the K9 rack I had previously installed. The rack install went smoothly but had a crap load of bolts/nuts to tighten. The ladder was another story all together. First of all, it cost $160 which IMHO meant it should have fit right out of the box, not so much. The...

Parting out one of my trucks. It's a 02 D2 in darn good condition. There is no engine but if your D2 is beat up or rusting out you could do a quick engine swap. I'll sell it outright for $1000 or part it if no one wants it whole. Clear title.

It's been a busy day. I decided to install my trailer harness in the LR4 today after the roof rail install. It is straight forward using the info at https://www.disco3.co.uk/wiki/Owner_Information_Mirror although my harness was slightly different than the ones shown there. There's one bit I'll...

I ordered rails, CAB500120PVJ, from Rimmer Brothers for under $300 shipped. These arrived in 4 days to the east coast via DHL. The instructions pointed to a Land Rover website but the instructions weren't available there. I went over to Disco3.co.uk and found what I needed plus much more. The...

Land Rover saw fit to ignore a 12v aux power source in my '13 LR4 base for reasons I really can't fathom. The base does not have rear climate control but the harness is there. I traced down the rear blower fan power (switched) to connector C0839S on the driver's side of the vehicle. It is a grey...

SD rack and rear ladder for sale. It is presently mounted to my D2. Lights are not included. $800 delivered within 100 miles. $750 local pickup.

I'm running a 'reverse auction' on this truck and hoarded parts. Project '90 RRC 99% rust free body. Macco paint a few years ago. Stripped interior but most pieces there except seats. 3.5 block under 3.9 14cux fuel injection. Engine ran when parked. Cannot run now because cats were removed and...

D1/D2 rear ladder - $50 plus shipping D2 to D1 CC ecu (AMR5700) - $50 shipped D1 front seats (decent condition) - $80 pair plus shipping RRC 4.2 ECU (AMR2943) - $100 shipped RRC rear bumper end caps - $50 shipped (one will need stud replaced but super easy job) RRC distributor - $50 shipped RRC...

I'll be there. If you'd like to swap your D2 rack for my D1 rack we can do it there.

I've got a ARB Touring rtt, in excellent condition, with the lower privacy room for sale. The vinyl cover was replaced in the last couple of years too. I'll be using it through the weekend at Uwharrie so you can see it in use and overall condition. We can remove it for transfer to your truck or...

D1 windshield seal kit - $200 D1 complete rear bumper (black) in great condition - $50 RRC fan resistor pack (AB) NIB - $50 Plenty of other D1 and RRC parts available. Take advantage of no shipping costs. PM me with requests.

I'm in the process of replacing the ball joints (hate that job), drag link & tie rod and the hub assemblies on the front axle of my '02 D2. I didn't want to reuse the spindle nuts but thought I might have to with a time crunch for Uwharrie. I couldn't find a stocked D2 nut in the local auto...

What is anyone using as a viable replacement for these dang plugs. They allow access to the TQ converter bolts. Every one I've touched is soft and swollen and is reluctant to or downright refuses to stay in place.