Search results

Is there a quality center ball replacement out there? Or a part number or is it standardized amongst any double cardan joint? I bought a D2 front shaft for my D1 and I’m replacing the u-joints and I noticed that one of the needle bearings is broken in the center ball. Thanks

I'm looking for specs on two different combinations. I'm not around my truck right now and didn't know if someone knew off the top of their head. Discovery 1 - Driveshaft Nut & Bolt length and thread pitch - Front of rear trailing arm bolt length and thread pitch Thanks.

Anyone else have this problem? I installed a Terrafirma medium duty 2 inch lift kit 15,000 miles ago on my truck. The truck actually lifted 3 inches. The supplied shock was rated for stock or up to 2 inch lift. first time in the woods with it, BAM...

On my 98 D1, What is the best way to change the front pinion angle? I have a 2 inch lift which I know everyone is going to say the pinion angle shouldn't be affected but I measured it last night.. I put an electronic angle finder on the front drive shaft and zero'd it. I then placed in on the...

This all started with a camshaft replacement job on my 98 D1. Timing cover went back on and couldn't prime the pump, timing cover came back off, packet the pump, got oil pressure but very delayed like 30 seconds or more after every shut down. I removed the timing cover once again, replaced the...

Good Morning, I'm replacing the oil pump in my truck. I bought the new pump, the pump I got is from Allmakes4x4 with a 'made in china' on the box. Any experience with this pump or should I throw it away, start over and buy something that's higher quality?

Good Morning all, are there any options out there for caster correction using the stock radius arms?

Good Morning all, I have my motor back together and can not get oil pressure. I inspected the pump while it was a part and packed it with assembly lube when it went back together. I have cranked and cranked and cranked with no success. There has to be a way to prime these things? Any tips would...

Cam going flat? What causes this? 98 D1

D1 4.0 liter. Has anyone used roller lifters in these motors?

What are the Ideal cylinder psi numbers on a D1 4.0? * Does 190psi seem a little high on a stone cold motor?

Good Morning, What brand main & rod bearings is everyone using with the highest quality? I have the same question for piston rings as well. Thanks. - 98 D1 4.0

Right rear tail light wiring. Does anyone know what the factory trailer wiring plug is supposed to be? It looks like a flat 4 was spliced in and it only runs my trailer running lights and blinkers. I'd like to take it back to factory and use an adapter for what I need. It should be a 7 pin right?

Good Morning, So I've run into a little bit of an issue and would like to pick everyone's brain. I just bought a pop up camper and the thing weighs 1,500LBS dry. I pulled it home with the D1 and I could barely maintain 55mph with deceleration on small inclines and sky high down shifts. I've got...

98 D1 - For tightening the wheel bearing nut and lock nut, Does 45ftlbs seem too tight? Or should I go off of feel and not worry too much about it? I'm chasing a grinding vibration on deceleration at higher speeds that becomes constant at 70mph and above. Accompanied by and intermittent unwanted...

Are there any AEL Fuel Pump Alternatives out there? Any Cross references or cheaper options? My 98 D1 pump works just fine but I'm only seeing 30psi. Regulator is working, lines are all clear, fuel filter is brand new, fuel pump was a rock auto purchase 2 years ago... I'd love to put a new pump...

I'm looking for a used working Cruise Control Vacuum pump for my 1998 D1

Good Morning, Does any one happen to have a vacuum line diagram for the cruise control system on a 1998 D1? Mine is incomplete and would like to piece it back together. Thanks.