Search results

Hey guys, Its me again, the ignornant guy with all the questions. If I start to bother you, just let me know and ill send my wife over to give you pleasure! This rover is for her anyway, she may as well help out! :-) Ok went to buy the RRS and suddenly felt like I was going to crap...

Hey guys, My wife and I set out to find her a low mileage and clean 2004 Disco. However, we got discracted by a beautiful RR sport. The price is fair and the deal on my trade in is acceptable. BUT!! Is this a good year? It seems like there is always a certain year to avoid with anything...

Hey guys, help me out if you can. Its a 98 d1. it will crank up fine and idels fine, however it will not rev up past 1,500 rpm. it starts spitting, spuddering and backfireing. It sounds just like it has jumped time, but I have never seen a boring old mod. engine jump time. Is this...

I am away from my rover this week and would like to buy this tool before I get back home. Is it a 42mm or 36mm? I have seen many posts on both. The direction on the threads is normal correct since it has one belt? Thanks

Hey guys, I am wanting to build a nice trail truck and hate to use a "real" 90. I am a petty decent fabricator and want to start with a frame and body. Frames are easy, but I have not been able to find any type of aftermarket body. Does anyone make one here in the states or can one be...

Yesterday my wife calls me in a panic. She is at the doctors office with our 10 month little girl and her 2003 Disco. will not start. It will turn over but no start. She tried several times. It took me about 30 min. to get there, I tried it once and no start. One final try and it cranked...

This is a boring warranty issue but id appreciate your thoughts. My wifes 03 Disco. is currently at the shop getting some warr. work done. When we bought it at this dealership we paid the extra $1,800 for the 100k warr. The disco was used with 40k miles. I was told it was a bumper to bumper...

I searched every way I could think of with no results. I am going to fab up some sliders for the upper sides of my disco. I am thinking about two horizontal bars, one going across the alpine window and one below it about 3 inches below the rain drip sill. I am sure I am not the only one that...

Just alittle something I built over the weekend. Its all 3/16" plate. Where it bolts to the diff I doubled the plate at the diff and welded another plate under it to go under the pinion. This gave alittle extra room incase a rock bends it up. Since I put sides on the pinion guard I drilled...

My D1 is no longer a DD and I think it needs some TSL's TSLSX's or something like that. Since Interco is not known for their sizes to be very true (32" SX runs short and a 33 TSL runs tall) I would like to see some pictures of Discos on swampers and alittle info about the lift they are...

Im not talking duct tape, extra batteries for your MP3 and cold beer!! I want to know the special tools that are commonly needed for rovers. I recently broke a inner front axle and here are a couple "non-common" tools I needed and now carry. A 14mm ratchet wrench for the bolts that hold the...

I just finished the install of my 4:11 gears and Detroit/Trutrac combo and broke something in the front the first ride out. I have not had time to take it apart yet but im still looking for alittle advise, please dont flame! I was trying to cross a rut and the pass. front tire was in the air...

Last week I had gears and lockers (truetrac front, detroit rear) installed in my 99D1. This is my 3rd rear detroit and this one acts alot different and I think something is wrong. But since this is my first all wheel drive application I though I would ask some questions before I took it out...

Im pretty sure this is a stupid question but since gears and lockers are so expensive I figured Id ask anyway. I can run a full synthetic in a truetrac correct? The reason I ask is because I ran a clutch style truetrac in a camaro years ago with full synthetic and it caused the clutches to...

I did a search but could not find what I was looking for. Maybe someone can point me in the right direction. I am currently running a 99 D1 with 2" lift and 265's. I am thinking about going with 4:10 gears and trutrac / detroit combo. Questions. 1. Will I notice a big power diff? Low...

I am looking for one factory alum. wheel to use as a matching spare. Doesnt have to be perfect. Its the five spoke style.