Apx. 117k miles with apx. 8,000 miles on a new custom 4.6 Bosch engine running Hedman Hedders and flexalite electric fans.
You are buying the engine at this price and it comes packaged in a 1998 Discovery. Drive as is or take the engine and sell off the rest of the truck. Conversion included...
I felt like saying this the last time I looked at this job, but maybe I'm just getting more curmudgeonly with age. I just wanted to send a special shout out to the twit who designed the crossmember on D1s. I could have pulled the engine in the time it took to try and drop the trans pan. Even...
Looking for a set of all three transmission hose/hard lines for my 98. Have a hole in one and figure I might as well replace them all. Don't have to be new, but must have a lot of life left if used. Quote with shipping to 14850.
Thanks.
1998 D1 Disco with a late DII 4.6 engine. Previously I'd been occasionally seeing code P0130 and P1138 pop up, not at the same time and not very often. They might show up then clear and be gone for a month or so. Scanguage is showing functioning O2s, but every now and then it slips to open loop...
I was getting all excited for this big snow storm we're suppose to have, but it looks like my Disco is going to miss the fun. I was pulling through an intersection when the drag link snapped, no potholes, no trying to turn the wheel without moving, just plain snapped making a lazy left turn...
I'm looking for a silver/gold passenger side front bumper end cap for a 98 LSE, the part that holds the corner running light.
If I can't find one I don't have to paint, the rest of the bumper is at the point where this would give me an excuse to rip it off and add a real winch bar instead of...
Any one running a mean green or britishstarters.com starter on a D1 running headers? I'm running heddman hedders and I'm assuming a gear redution starter will fit since they look smaller than stock, but the housing looks like it comes off at a bit of a different angle and it is already damn...
It is about 10 degrees a good foot of snow with more on the way here in central NY and it is a reminder of the good and bad of Land Rover ownership in the winter.
The good: can drive out of the driveway without lifting a shovel.
The bad: this annoys the neighbors.
The good: can plow through...
Need the hinges for the tailgate. Only the bottom one is broken so that is the one I really need, but I figure the top one may go soon so I'll take both if you have them. Anyone who happens to have them in the 98 LSE silver/gold color that is an added bonus.
Thanks,
Evan
I searched, but couldn't find a definitive answer to this question. Anyone know if the lower hinge pin on the rear door of a D1 can be tapped out? It broke into three pieces when I opened my door. I'd like to just hammer in a grade 8 bolt to make it useable until I can get a new hinge, but if...
I finally got around to posting pictures of my GEMS 4.0 to Bosch 4.6 conversion project. It was a full swap, I used almost everything on the Bosch engine including the 4.6 oil pan and front cover.
This is where the project started:
http://discoweb.org/forums/showthread.php?t=16182
I wrote up...
Any one know if there are oxygen sensor wire extenders available for a 98 Disco? I know the Ford and GM guys use O2 extension kits, but do any of them plug into Rovers? Trying to avoid some splicing.
Evan
I need the bumper tail light bulb socket for a 98 LSE. It says Kilgass on the side and PET 30GF in the socket part. part # XBP100180.
It is the two pronged style holder.
Contacts in one of mine rusted apart.
Thanks,
Evan
I need to seal up the secondary air injection ports on a 2003 4.6 engine. Does anyone know the thread pattern/size of the holes. It appears, as usual, it is some pain in the ass pattern as NPT stuff doesn't fit. I need to plug the holes ASAP to get the Disco back in action to help with a move...
I need one of those rubber seals that goes in the circular hole in the D2 4.6 oil pan to allow access to the flywheel bolts. Shoot me a note if you have one.
Thanks.
What are the 4 holes, 2 per side, that are threaded and come out of the block right next to the middle two exhaust ports on a D2 4.6?
Anyone know what year they started tapping that space out as the hole isn't there on earlier engines.
Thanks
Hi,
I'm looking for one knock sensor that has the right angle on it. I think the part number for the D1 part is ERR5594, but I need the one that comes out at an angle not straight.
Thanks,
Evan
Busted the crank sensor heat shield on a GEMS 4.0. Considerig the splitloom on the wires leading to the sensor has already melted off I'm guessing this is a fairly important shield.
Thanks.
Some of you may remember my 1998 LSE dropping a sleeve this winter and destroyed a pair of pistons.
I finally have a new Bosch 4.6 engine to drop in. Before I do the conversion I wanted to make sure I had all the correct info when it comes to making the swap from GEMS to Bosch.
I plan on using...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.