Search results

I am getting ready to do the head gaskets on my Disco. to try to save down time I was going to buy heads already redone. Atlantic British and a few other places sell them. Curious if anyone else has gone that route or have recommendations for where to get them. Thanks

I am getting ready to do the head gaskets on my Disco. to try to save down time I was going to buy heads already redone. Atlantic British and a few other places sell them. Curious if anyone else has gone that route or have recommendations for where to get them. Thanks

Does anyone have any idea what size that bolt to remove the centering pin on the rear diff flange. I have exhausted my bucket of spare bolts and haven't been able to find one that fits.

I am just considering this but I thought putting out a feeler might be a good idea. I have a 2002 D2 and would like to try to trade for a Range Rover. I need a daily driver/trail truck. Would like a bit more space that the D2 has. If there is any interest or if anyone knows someone that...

Anyone here using one. I like the look of it but would like to see more pictures and hear from those that are using it. Thanks

Anyone selling one? Prefer one without the brush guard. RTE maybe?

Talked to Justin at Lucky 8 and he put the idea in my head. Aside from notching the plate to let the shifter move to the side is there anything else I need to know about before I buy one and give it a try?

This morning the truck left me a present in the form of a couple drips of coolant on the garage floor. Popped the hood and saw some fluid in the back corner of the valve cover gasket. Its coolant. It seems to be leaking from the back corner of the drivers side valve cover dripping down onto the...

Silly question with even sillier reason. I am going to replace my O2 sensors but, if I have to disconnect the battery I dont have the radio code to get it to work again. Is there any reason why I cant just replace the sensors without disconnecting the battery.

And with what. OEM prop shaft is around $300.00? Tom woods closer to 600. Since it is apperently a time bomb and my truck has 105k on it. I am not sure about the service history of it after the 70k mark since it wasnt serviced at a LR dealer after that according to the carfax. Should I just...

When my truck is cold and I put it into reverse it thunks. Cold going into drive goes smooth as can be. If i let it warm up a bit it's less. If I let it get really warm its smooth. once its warm no thunking and the transmision shifts smooth otherwise. Anything I need to be concerned about...

So my new rover that I thought was leak free (as much as a disco can be anyway) has left a couple drips on my driveway. It appears to be comming from the back corner of the valve covers. Would it make sense to replace these now or, since the truck has 105000 miles and I am assuming the head...

disregard. short wifey and independent daughter who likes to climb in the truck on her own demand I keep them on. With the lift they don't look too bad. Ill just say i need them to get to the roof rack.

Maybe not but it is at best the most non life threatening question. My new to me Discovery only came with one key. It has the keyless buttons on it. Do I need to get another keyless entry key or can I just get a LR key blank and have Lowes cut me a new one. Just need to have a back up key...

So after selling my 96 discovery almost a couple years ago I decided that I was happier with a Rover. So I found a good deal on a 02 D2. Yes I know it's not the most desirable year. No CDL. But I never really did any serious off roading with the old one beyond some easy trails and camping...

http://www.spazoutny.com/ironmaiden.htm :rofl:

Anyone here into kayaking. I am looking for one to get out on the lake> Anything to keep me out of the gym in the summer time. Any suggestions on an inexpensive boat? Not going to be extreme whitewater, just get out on Lake Wylie and paddle. Figure with that and cycling I won't have to...

So i go to Auto Zone to find the front wheel bearings and what do ya know they don't have them. they have the rears though, Timken 37. From what I read in my search the 37s fit the front as well. Before I go to the zone and get 8 of em. Is that actually the case? Anything else I should...

All the black rubber bits on my truck are so oxidized that it makes waxing the truck a excersize in futility. Accidentally hit one of the window seals, or anything rubber for that mater and i get black streaks. I have tried lathering the stuff in armor all. Hiting it with a scotch brite pad...

I am looking for a D1 factory brush guard in my local area to keep shipping costs down. Or maybe a local pickup. I am in Fort Mill SC which is just south of Charlotte NC. Also if possoble the side pieces and front air dam with or without fog light cutouts. My zip is 29708.