after the battery ran out of juice she started up just fine.
Guess the ECU resetted or ? (and adjusted to the new MAF)
Still have low vac, did build myself a smoke machine but couldnt find a leak.
on my DII i changed the MAF and the car ran like s**t. Black clouds behind. Tried to disconnect the battery for 10 minutes, but no change.
Was going to take her to the dealer for a reset of the ECU but when i took a week. During that time I accidentaly left some light on and drained the...
I have checked for leaks but can't seem to find one.
What is the best way to check if I have a leak at:
1.Gasket at upper/lower intake
2. Injector Orings. (didn't change them, only lubed when rebuilt)
Little Update.
It runs ok until it goes into closed loop for fuel-system (when working temperature) It "smells" when warm. Is that Nitrous gases?
Runs like it has a falty O2-sensor (idles up and down and even dies) but no error-code on the ODB2
On the ODB2 the Absolute Throttle Position looks...
Changed the MAF and now it runs ok on cold starts now (used to die when giveing throttle)
However it now throws out plumes of black smoke when pushing the accelerator. And also dies on idle when warm. And dies on acceleration.
Before change of MAF there was no black smoke
Will the ECU reset...
Have checked all tubes and still no change in vacuum.
Around 14, steady
(When throttle is opened and closed rapidly it falls to 0 and swings back to 18)
So I have 3 options:
1. "IGNITION AND VALVE TIMING:
2. "Poor rings"
3. Or a leak
First question
What is the best way to check for a leak at...
thx, i'll have a look for leaks. One clarification. When she was stalling earlier the vacum was even lower. suddenly it jumped up and the engine doesnt stall anymore. She runs pretty ok, maybe a little weak, but not at all as before. I think I had a leak at the servo-pump-connection (where I...
ok, let me rephrase question. Maybe to much text above
1. Is 14 to low vacuum? (Guess it is, but car runs ok)
2. Is it possible to use Chris tip for measureing on a -99 V8 (no rotor)
thx in advance... ;)
My disco -99 V8 has been weak and "dying" when giveing throttle in neutral and also really weak at higher speeds (like maybe 100-120hp).
I connected a vacum-gauge, since it didnt fit the connection I removed the steering-servo vacumline and put my meter there. It read 8 when cold but suddenly...
After getting my engine back from rebuild there seems to be no oil-separator in the right-hand rockercover-intake tube.
I'm not sure if it wasn't there before or if they have not refitted it.
Any experience on driveing without it?
It's a disco-99
Dicscovery -99 4.0 with rebuilt engine and heads, new pistons
1 - 151
2 - 154
3 - 151
4 - 149
5 - 152
6 - 146
7 - 142
8 - 148
I have not done a wet-test yet.
I can't seem to find anywhere what it should be. Have searched this board, googled and raved.
on a 4.0-99 DII
what is the exact procedure to measure if the fuelpump/pressure is ok?
I have the gauge to measure it, but where
Should I disconnect the fuel-line from the lower intake-manifold/injectors and "crank". Happy for some step-bystep instruction!
When does the fuelpump build...
ok, after connecting a new battery to the starter nothing still happend. but i found out that tha battery in the discovery had alot of "Juice" in it.
So finaly I cut the hood-latchwire in the front and opened the hood that way. The alarm went off and after that everything worked again. The...
I ment key-hole in rear door. Is it "standard" on DII?
Where?
The pics in the rave give an pretty good idea, I hope its not "superlocked". Do the DII's superlock?
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.