Search results

I've got a '95 LWB I've been working on. I went to check the oil in the front diff and found it badly in need of changing, drained it out, flushed the diff and refilled. I managed to drop a bit of plastic tube I was using as a filler extension into the diff, and after three hours of trying to...

1 pair, brand new still in the box in bubble wrap sleeve. These are getting hard to find. Selling as a pair only, will not separate. They have the newer style rectangular plug but you can swap your old plug if you have the round style, or I can supply them already swapped. $200/pr. Shipping extra.

2001 DII with slipped liner. Odo reads about 75K miles. Decent grey interior, though there's a small wear hole on the edge of the driver's seat. Lots of good parts available, and I have a lot of parts from a 2000 DII including a few doors and hood in Champagne. Located in Santa Rosa, Ca.

39.5 Super Swampers on 15X9 Steel Wheels The tires aren't great but still have a few off-road miles left in them. The wheels are practically brand-new, installed on the truck with some used tires and then never wheeled, it just sat for several years. Nothing but some dirt and such on them...

I have this nice, one-off roof rack that was custom built for a Range Rover Bobtail. The box itself measures 38.5"X54" outside dimensions. It's very well-built, not a thrown together POS. I put it on my '91 just to see how it looks. The way it's constructed, it's made to sit all the way forward...

I'm working on a '99 DII for some friends. This truck has been beat, driven hard on long bumpy dirt roads to get in and out of their ranch for years. The turn signals, flashers and power door locks don't work and I've been trying to get them sorted out. I'm not terribly familiar with DII...

I'm curious about the differences in 14CUX ECUs over the years. I know the EPROM chips are different, but disregarding the chip are there any other real differences, upgrades etc. between say a 1989 ECU and one from 1995? If you took an early 3.9 ECU and plugged a later 4.2 chip into it, would...

...need one for a truck I'm working on, so if anyone's parting a '95 and has a good one, let me know. It's the piece in the pic:

Working on a '95 LWB with memory driver's seat. It doesn't work in two positions, back or forward, and rear up and down. When I jump it at the plug in back it works fine in all positions, so there's nothing wrong with the motors. When I activate the switch in the two non-functioning positions I...

Sorry to write a small novel here, but I believe in giving as much detailed info as I can.:D I installed an R380 from a '97 DI in my '91 RRC back in Feb. So far I love it, but I've got a few electrical glitches. First, just to detail what I did to complete the install: Got a complete R380...

No longer available.

I've been having a bit of a problem lately. When pulling a hill or accelerating fairly hard in my '91 RRC 4.2 the CEL will sometimes come on just when I ease off the throttle. Checking the Onboard Diagnostic Display shows no codes. Reset and continue and at some point it happens again. I have a...

I'm looking for a 24-spline Locker, preferably a Detroit for the rear of my RRC. I need HD axles too. Trying to save a few bucks over buying new, hoping there's someone out there in the process of upgrading to an ARB or something. Eventually want to put a TrueTrac up front but just want the rear...

I got Cambo's '95 4.2 after helping him swap in his 4.6. It was a good running engine with only a lifter tick. We had to cannabalize it somewhat for the 4.6 swap, taking off the pan and pickup, front cover, intake and valve covers. I brought it home and then took the intake, front cover and...

I need to know the bore size (I/D) of the clutch master cylinder on a '96 manual tranny DI. Anyone know what it is? I'm missing one entirely and need to find out if I can just kit one of the several Lockheed/Girling clutch M/Cs I've collected over the years from various English cars and use it...

Parting out 1989 and 1992 Range Rover Classics. Doors, rust free upper tailgate, 14CUX ECU, 3AM and 5AM MAF meters, ZF automatic transmissions, VC transfer cases, 10-spline diff/axle and suspension systems, good backseat from '89 in Sorrel Brown with vertical pleats, good Sorrel Brown backseat...

This may sound like a strange question, but will the torque converters interchange between a '97 P38 4.6 and a '95 RRC 4.2? I realize the depth difference, but took some careful measurements and found that the total depth from the block face to the tq. conv. hub/pump drive that inserts into the...