Search results

2003 Discovery S, 72k miles, epsom green, 2" OME lift and shocks, SS braided brake lines, trailer package, locking TC, 5 new 275/75 R16 Kumho with 200 miles on them, spare relocated plate, all the gaskets on the top end replaced, new water pump and t-stat (did not get hot, I had front cover off...

I am interested in seting up my own sliders also. I have never had a chance to look at a rig up close that has them. My question is where do they attach to the frame? Anyone willing to post a pic of the underside? Also curious about the airbag effectiveness with the aftermarket bumpers. Do you...

They only have 1 for the rear from AB. I am pretty sure its a wabco/LR

If you are still looking for a mount I have some 2-1/8" x 1" thick spacer brackets. They wont work with a 16" rim because the rim hits the stock mount. Will work fine with a 18" rim, or you could space them out and use with 16" rim. Ill sell them for $75 shipping to lower 48 included. Have 4 of...

I didnt re-pin it I spliced just before the ecu. The wire already has a splice by the rear tire. ABS light is on when started, 3A's +Brake come on after about 5mph. Code reads as copied on the first post of this thread. No sign of water anywhere on the truck.

Thank you for the reply. I expected the same outcome that you got. Unfortunatly my codes and A's are still there as logged faults.

No active fault but it keeps lighting up the 3-A. Origanaly the code was for the right side, until I swapped. I wish that LR and Wabco had left the plug and play sensor alone. Would have been nice to just plug it in and not have to question my splice changing resistance. Has anyone else used the...

I had considered that, but the code did move from wheel to wheel with the sensor.

2003 Disco S, 72k I have done step B repair and lights went off. Installed new braided hoses when lifted, akibono pads all the way around. Light returned a short time later with a RRW poor connection code. I checked ohm reading and it was in spec. So I swapped the RRW with the LRW sensor...

03 Disco II. Emptied the Macalin last night so back to work now. Going to try using crimp ons and self fusing electrical tape for the connection. If it still codes I will be on the phone with AB in morning. My guess is that I screwed up the resistance level with the solder joint. Or I am getting...

I have never done a heater core in a Disco. Typicaly you dont have to pull the dash just a peice of it. As MrT said people who have done a few in Discos probably have figured out better ways.

Heater core or line going to heater core fail. Get a light and maybe a mirror. Start at the top and look for the wet spot.

P1590- Rough rd--new 045- switched sensors determined it was sensor. New sensor spliced and soldered. still there. Cant be hub, sensor was switched side to side. P1412 & 15- SAI valves. Mechanic fixed a vacuum line reset and they were gone for a couple days. After new wheel sensor they showed...

I was hoping the rotella (also diesel oil) would clean out the sticky lifter. So far it hasnt, thats why I was wondering about added detergents. I have only driven it about 300 miles since the change

I have a valve tap that showed up after I put the top end back together. Engine was dirty so very possible its just carbon that got knocked loose. I am running rotella. Anybody ever try running cam2 to wash out the engine? anyreason not to try it?

I screwed up the old connector so thats out. I am planning on splicing above the connector. Solder, liquid tape, heat shrink individual leads, then heat shrink the whole lead with adhesive filled heatshrink. Thats the way I do all my boat connections. So far (5 years) I havent had to go back on...

I had a code for RR wheel sensor. Swapped the sensors and the code was then on the L. So I ordered a new sensor from AB. Problem I have is that the new sensor has about 20' of wire to go back to the SLABS. I really dont want to run the wire all the way back and locate the connection. I tried to...