Search results

http://charlottesville.craigslist.org/cto/5578947833.html

After 6 years of owning a 92 RRC i finally ran out of patience. I cant afford to keep a vehicle that requires that kind of maintenance and expensive parts. I just replaced a T-Case, rebuilt a rear diff and still has a vibration between 20 and 35 MPH. I would like to know what these things...

I recently started getting vibrations and grinding noise while feathering the gas on my 92 RRC. I decided to replace the T case output shaft bearings as i noticed a little play. When i pulled out the rear bearing housing (after way too much effort) i end up with this. Has anybody...

I have an original radio from a 92 RRC. I have the code and instruction manual for it. Everything works, just went to a new unit with USB and Bluetooth. $50 plus shipping. Gabe.

I was eyeballing a new project when i found a Disco I for sale. It has over 200,000 miles on the 4.0 engine. The previous owner had an over heating issue and drove it home anyways:banghead:. Once there, the truck would not start up again. It sat for over 5 years until he decided to put it on the...

Any tips on how to adjust backlash? I just replaced the swivel grease, can i remove the entire ball housing assembly in order to remove the axels? what is acceptable pinion to ring gerar play? Thank you; -Gabe.

I just installed a new Pertronix distributor on 1992 RRC. its NOT the expensive performance one, its the direct replacement one...anyways, after installing it i adjusted the timing to 6* BTDC, but when i check it whit a timing light it looks erratic and shifts up and down (vacuum advance...

Im not sure what these things are called... I would need all 4. Let me know how much for them shipped...

I bougth a set of used RTE 6* corrected radius arms. I installed new poly bushings, sanded and painted them. But they will not work with my 3" lift. Im never going to lift it enough, so im selling them for what i got in them $250 OBO. I can try to figure shipping on your dime, but they are so...

Im looking for a RRC ABS swivel ball, driver side axel with CV joint and a stub axel. Im on a bit of a budget. Let me know if you have some and how much for them shipped to Virginia 22980. Thank you. -Gabe.

Anybody seen this? Looks clean for $600... http://washingtondc.craigslist.org/nva/cto/5011739852.html

I bought a set of used RTE radius arms. I though they were 3*, but turns out they are 6. So now I would like to find someone who is in need of a set of 6* arms and has some 3* arms laying around to trade. I would rather not sell, but if it comes to that I might consider it... Here is a picture...

I bought a set of used RTE radius arms. I though they were 3*, but turns out they are 6. So now I would like to find someone who is in need of a set of 6* arms and has some 3* arms laying around to trade. I will sell them for $250 plus shipping. New poly bushings installed. Here is a picture...

I just installed an used set of rovertym 3* radius arms. I wont go into the deyails of the hell it was to get them on. But after it was finished, I noticed the front driveshaft rubbing a crossmember. I drove it, and I feel a vibration. I have pictures of the crossmember touching the driveshaft...

Im looking for a set of radius arms for a RRC with 3" lift. Let me know what you have and if you can ship. Thank you.

Ok, I did some research around the site and was unable to find an answer for this. The oil light on my 92 RRC comes on intermittently after warm up, after driving for a while, it comes on solid while idle. I would like to replace the oil pump, but I find all sort of different looking things when...

The Hog :: 1992 Land Rover Range Rover (2015-04-27 20:07:57)

A few days ago I noticed water collecting on the floor boards of my 1992 RR. I traced the water leak to the sunroof and figured a clogged drain was not letting water out of the collection channel where it was pooling and dripping out. I tried to unclog the hose, with no success, after running...

The Hand Brake cable on my 92 Classic snapped. Im replacing it and hit a brick wall. I disconnected the old one from the handle by removing the cubby box liner and shifter plate, but i cant get the cable disconnected from the brake drum. I removed the pin, and the cable is loose, but there is...

Found this on CL. I live really close, see it on my way to bald Mt. Trail. Looks nice and stock. http://harrisonburg.craigslist.org/cto/2916978892.html -Gabe.