Search results

Anyone in or near Asheville, NC with an ABS Amigo? My son has my old '04 Disco and the 3 amigos just came up (no history of this problem with the truck). Hoping to find the codes to see what faults are present to start figuring it out. His ODB II scanner won't do it. Not sure if it is...

Find a good indy Land Rover shop to look at it, not a regular shop and not a dealership. My 04 lasted 103K before head gaskets were needed but nowhere near that amount of coolant loss. Maybe a bad motor, maybe not, no way to know until someone who understands these motors looks at it. Will...

I had this happen on my '95 about 6yrs ago. I ended up using some aluminum flat stock from Lowes and cut it out with a coping saw and then shaped it with a dremel to match as best I could. I didn't take pictures but the single thickness worked perfectly. There was one part of the plastic ring...

Paracord or the like. Just weave it from side to side on the seat frame to create a support for the seat itself. Not too tight, not too loose so it gives a little and is not too hard. Give it good coverage like a spider web, maybe put a piece of heavy cloth or thin rubber matt on it then the...

Look to see if the felt seal the window travels in has moved downward. the rear vertical seal had dropped down a bit and was the culprit on mine and would create quite a bit of noise. I was able to pull the seal back up but it kept going down a little every time I lowered the back window until...

Yes I put sealant around the coolant passages and at the end gaskets.

I just replaced the alley gasket on my 04 DII due to a coolant leak. Got everything back together and now I'm getting codes (0130, 0150, 0174, 1174). Cleared those out, looked for vacuum leaks, missed connections and cleaned the O2 connections. Still getting 0130 and 0150 within a few miles...

I just replaced the alley gasket on my 04 DII due to a coolant leak. Got everything back together and now I'm getting codes (0130, 0150, 0174, 1174). Cleared those out, looked for vacuum leaks, missed connections and cleaned the O2 connections. Still getting 0130 and 0150 within a few miles...

Have you looked at the pinion bearing? I just developed that in my '95, put it on jack stands and turned the front shaft to confirm the noise is from the pinion. It was leaking a bit a grease so not surprising.

I'd clear them again and see what comes back. If you keep getting O2 errors the part should have a 1yr warranty if they are Bosch sensors. I had repeat O2 errors on my '04 at 90K miles. After replacing multiple sensors they were still there. Finally pulled the injectors and had them cleaned...

How about the outer plastic cowl under the windshield. Mine is cracked down the middle. zip - 28562

You can easily pull it and gut the cylinder or take the cylinder to a locksmith and have them gut it for you, no one will know but you. I had the same problem, pulled it and took it to a locksmith since a pin needed to be drilled out to pull the internals.

Thanks for the quick reply. Bear with me as I am an electrical NOOB so I'm going to ask some dumb questions as I've never used a multi-meter. How can I ID the primaries/secondaries, and better yet how do I only power those given the relay fits into a socket? If I am following your explanation...

I noticed this weekend that the relay under the passenger side dash that controls the aux fans on the radiator when the a/c is turned on gets VERY HOT on my 95 D1. Actually my son found out when his toe touched it. I had replaced the relay some time ago as I had an issue with the relay...

http://www.fluid-film.com/ I use Fluid-film to coat the frame and underbody seams each year. It is a great preventative and will stop rust from progressing. No rust at all from beach driving.

Check your base idle. I had a similar problem and once I adjusted it my idle issues were resolved. I pasted the procedure from an old posting below. I used the dashboard tach to set it, not exact but it idles well now. Atop the plenum, you will either see a smooth cap, or, it was was...

If you pull the injectors you can get your injectors rebuilt from several places. I used Fuel Injection Connection for $16 an injector. They are in AL, took about a week between sending out and getting them back. Witchhunter also does this. Made a heck of a difference. Have you checked the...

Flying Circus in Durham is good to work with if you need more work done. they have been fair to me the few times I've been there

Could be your injectors as these are lean burn codes. I was having issues with o2 codes and a lean burn that turned out to be two clogged injectors. I'd rule out other causes first as pulling everything to get at the injectors was a PITA as it was my first time. Sent them to Fuel Injection...

It ended up being the injectors. I had already replaced the 02 sensors (under parts warranty) with the codes coming back each time. I pulled the injectors and sent them off to be cleaned/re-built. 2 of them were definately not up to spec and causing the cylinders to run lean. After rebuilding...