Search results

Need the relay for the d2s blower motor (2001). Thanks, please Pm/email me.

Can the D2 pitman arm be reamed out for the Chevy 1 ton tres, safely? I'm thinking about running crossover steering with the chevy 1 ton y link on my 80 axles with hydro assist.

I have a bad catalytic converter. I need to replace it soon. Its loud and annoying. I'm doing an axle swap soon and want to link the front end. I can't run the stock exhaust with a linked front end as it'll be in the way, so buying the OEM part is out of question for me. I would if it was that...

Into a D2, worth it? I'm rerouting the exhaust already, so I don't care about fabbing up a custom exhaust. I thought if I could gain a few of anything it would be nice, because I can buy a set for 80-120$ on eBay or something. I'm going to swap cams later down the road also, so if the p38...

I saw this build page on eastcoastrovers.com were they did a D2 and put an air compressor behind the cargo box, it looked very clean and I'm interested in doing the same with my D2. I have a 2001 with the grey interior. Price shipped to 89130 please! Thanks, Dane.

$1,500 from Lucky8; Front Cv's and Axles. Worth it or go an alternative route? What would we agree on the max tire size is for Ashcroft axles and for stock D2 Rover axles, realistically speaking of course. Thanks.

My front driveshaft failed and killed a diff. I've found a few from $75-$250 on eBay, I would much rather buy it from someone who knows that their differential is in working condition and who is an honest reputable used parts guy so I wont buy another one with the same problem as mine. It...

Whining noise on deceleration, I have a brand new driveshaft since my rebuilt one failed (person who rebuilt it ground down the center ball seat). It's a sounds like a bad bearing, just don't know how to pin point if it's the front output on tcase or the diff. Anyone know the size bearing for...

Is the D1 block the same as a D2's Block? I mean, just the block itself, none of the guts.

I'm looking to design and attempt to perfect for a versatile DD suspension system on SolidWorks. I have a lot of time in between this semesters classes. My main question would be what setup would the most versatile one for a DD but can really articulate at the same time. I'm not sure which...

I bought it for my first car to have some fun in it, while still being able to take me to college and back. Haven't been able to have much fun in it after what seemed like a never ending list of repairs since I bought it, but the gremlins seemed to have finally stopped, for now...:yawn...

2001 Land Rover Discovery II - Se7 - No Secondary Air - Fuel Pump W/ Advanced Evaporative Loss System (AEL) I had a hard start, replaced my gas cap, the hard start went away for a while, then suddenly came back. I removed my passenger rear jump seat, pulled some panels, and pushed the carpet...

I'm committing to building a bumper, my father owns a custom light fixtures fab shop so I have all the tools and resources to build a really nice one. I'm in Nevada so there is a lot of desert/mountain trails around here, my stock pre-facelift bulky turd of a bumper would hit nearly everything...

It takes two turns of the key to start the truck. from on to cranking (no start), then back to the on position and cranking it the second time it starts. What could this be? I'm stumped. I noticed crystalized coolant on a relay connection, could this be it? I have leaking valve covers as well...

I'm not sure if its a straight forward job or not, I have opted to stay with the rear air bags. I bought a +2" Med Duty front coils, +2" front and rear shocks, and some rear SLS spacers. The lift should be coming soon, by early next week, and I want to get as much knowledge I can before I tackle...

Im looking to buy a used block, preferably a 4.6. I have the Non-Lev Disco, without the SAI, do any 4.6 engines not have SAI or can it be deleted without any performance loss? my plans for the 4.6 engine are putting some flanged liners in it, performance cam, and new crank, pistons etc. As my...

Hello, My brother is giving me a set of Goodyear Mtr's 31x10.5R15, they are free, this is the only reason I ask. They have 1000 miles on them, he moved to a 35 inch tire for his diesel Isuzu project. I know dust guards need to be either trimmed or taken off, no big deal, but will they clear the...

I'm lifting the disco with a TF 2 inch lift. I need a new driveshaft, I rebuilt mine, but it's already failing, autozone u joints won't hold even heavy duty grease. I was looking at Tom woods' driveshafts, but don't know what one to get, there's a double Cardon one or a normal one that looks...

I asked another forum about this hum/vibration in my truck, it happens around 1100-1600 rpms, its the loudest when letting it wind down, all they kept asking was is if I had rebuilt my driveshaft, which I had stated that I had already. Don't get me wrong, the hum makes the truck sound cool, but...