Search results

Need the right hand side/passenger side tail-light (mine is cracked) for a 1994 D1, email hughes2925@hotmail.com if you have one to sell. Shipping would be to Greenville, SC area. Thanks

Email me at hughes2925@hotmail.com if you know where to find weather shields/ weather guards for the front windows of my 99 DII please. Thanks all! Nate

Every time it has rained lately it seems I forget that water pools on the top sill at the base of the safari rack. Put my windows down on my drive to work, turn a corner and then my left arm and shoulder get soaked, haha. Anybody know where to get the Disco II weather guards/ weather shields...

I used to have the A frame bar that attaches/bolts on to my winch kit for my 99 Disco 2. I need only that bar that is the A frame that attaches to both sides of winch tray. It is not wrap around, it's just the A frame bar, been looking on a million sites but can't seem to find my old winch kit...

Need a new or rebuilt 99 DII engine 4.0L. Email me info if you can help in any way or know a good place to look. I have seen many used on eBay but most have very high mileage. I am in no hurry, truck has to have heads and gaskets redone for a 3rd time and I am opting for a new engine instead...

It's the occasional power failure that I am worried about...that plus it only gets about 10mpg right now. It's like the truck is stuck in the "limp home" mode and all the heavy exhaust can't be good. I had the truck on inside my garage with the door down and now my garage door has a solid...

I did the "landroverclub" abs mod listed above with the wired bypass of the VS circuit on the modulator side using option B just as explained. Everything seemed to go smoothly, pretty easy to swap out the ABS modulator actually. It didn't clear up the 3 amigos however, still have a lit up...

No, I couldn't drive it around with either of the new MAFs I had purchased. Both just made the truck cut off after just a few seconds, so driving was never possible. I tried to restart the truck each time about 8 times I'd say. In each case I had to put my old MAF back on and it runs ok, not...

So, I did replace all 4 02 sensors this morning, very easy to do. Then I put the new MAF in place and hooked the battery back up and the truck won't stay on. I unplug the MAF and it runs just fine. I put the old MAF back in (that LR dealer said needed replaced), plug it in and it runs just...

99 Disco Series II; It seems awfully easy to replace this ABS modulator and then drain and refill the brake fluid (which I do every time I have done pads or even rotors). But it looks like "Test book" is needed. I don't have a computer code machine or test book (whatever that is). I am a...

I have 5 tires (Michelin mud/snow XTC's 16") that are sitting in my basement and they need to be used. They all are mounted on Rover 5 bolt pattern rims that came off my 99 Land Rover Disco Series II. To see the style online go to roverconnection.com and choose Disco II (99-04) under...

I already bought all 4 02 sensors from ebay for $80...they are used but it was a Land Rover parts guy on ebay with 100% feedback and over 500 sales. I will replace them in the morning and will repost the results. Light a candle for me! I imagine the 02 sensors are easy to remove/replace...

I never went below about 14 mpg for mileage. I never really had any problems until it started wanting to give out when just occassionally going from 0-5mph on a start, warm engine or not didn't matter, just intermittlently wanted to cut out on me. I will def replace the 02 sensors this weekend...

I have purchased a new MAF sensor for my 99 LR Disco Series II b/c the dealer said I needed a new one and also 02 sensors. I purchased MAF part off ebay and installed it. The truck won't stay running but chokes out after 2 seconds or so. I put the old one in and it runs, but not great, kinda...

I purchased a MAF off ebay (Bosch part number 0 280 217 532 for my 99 LR Disco II) but I assume it's plug in and go? I need this part if anyone has it, or an understanding on how to get it to work. When I plugged it in my engine would not stay on for more thann a second. thanks, nate at...

I have a 99 DII and cracked the transmission when my drive shaft broke. The crack actually/leak was coming from above sort of. Now that I have the transmission out can I weld it without taking it all apart? Thanks, Nate at hughes2925@hotmail.com

I broke the front drive shaft at the Ujoint and came to a stop after about 3-4 loud clunks...no transmission leak for two days, then leak came. I put a small crack in the trans...can it be welded? thanks for you help Nate

turns out i just needed new spark plug wires! all is well, thank heavens

I have a 99 Discovery series II that has just started acting like it is clogged or has bad gas- the service engine soon lights started flashing yesterday x 3 then just stay on. The truck is running up to normal speeds but keeps kind of cutting out and it is cutting out sort of quite a lot...

How do you remove the sensors b/c mine are doing the same thing on a 99 DII. I see the sensor wires going into the housing of the brakes but how exactly do I pull them? I have done my brakes/pads/rotors and can get that job done, but when it comes to the bearings, the abs sensor wires, etc I...