Search results

I have decided to sell my SD rack. It is made for a DII but I really like how it fits the DI. It has the farmtek flooring all of the light tabs, and all of the hardwear except two of the stainless set screws. I had completely refurbished this rack by straightening the whole thing out, cutting...

Be there or forever be a square. Already a few confirmed Rovers and we will be running with a group of Mogs. This is fairly early to run the trail, little to no rock stacking and the most lush scenery of the trails season. Also little to no fire restriction this time of year. Get it while...

Ok, I am at the point that I need to mount my Air bumps. I cannot just stab them in as there is a fair amount of thought required to make them effective. My problem is there is not much room in the front for the cans. I am looking at possibly fabbing up a landing pad off the axle towards the...

Need more length. I already have the "extended lines from Rovertym but with the coilovers I am maxing them out bad! Any suggestions, seems hydro shops in Reno are into gouging. I guess I could go to Earl's in Sac but I have no plans to go to the valley any time soon.

I can build one but I can also possibly find one for sale, got one? Gimme a holler if your selling.

Just got back from wheeling on Memorial Day. One of my friends runs a Dodge wrecker and said I could literally come in and pick out any set of 60's he has there. With my Coilovers and bracketry bits on it's way I figure it makes sense to grab these as qiuck as I can to get them into the...

Hub nut size? I am going to do my rear rotors and don't have the right size. Inner hub I think (it's the one that holds the whole bearing set together) nut 98 DI.

Long in the gears, hard shift, erratic down shifting, and slipping. Changed Fluid and filter and had Jiffy lube do a Fluid tech, still no improvement. DI w/183,000 miles. Is there any possibility it is the bands or Torque converter? What am I looking at in repair costs? For the sake of...

Ok so here goes. I have three Piaa 580 lights on my front bumper. I decided to relay each light. I built a harness that runs from each light to a dedicated relay on the firewall. Each relay is switched by the factory fog light switch (jumped from the first relay in the series to the next, and...

I have a friend that manages the Dodge wrecker in Rancho Cambodia and am considering a Dodge diesel swap. Any suggestions as to which motor will fit? I realize this is not an average swap but the cost and complications of a TDI swap are a bit difficult to swallow and the availability of a...

16x7 xs sport rims fit DI new at AB 1495.95 set of four. http://www.roverparts.com/Parts/ANR3631MNHGA.cfm I have five painted flat black with 4 Big O XT 255/70 R16 and one factory size Michelin. $500 OBO no center caps new valve stems and the tires have better than half the tread left. Can...

Check it. http://www.lrrforums.com/showthread.php?t=2359 See photos of the finished product. If you care to see the build follow the above link. Over tying to re-size photos right now.

So here I am getting ready for the DMV inspection to transfer mt Reg. to Nevada.... I've got a ho-made rear bumper and need to fix the annoying blinker problem. The blinker fix in the tech section says to use an EP-26 relay, however the auto parts store only stocks the EP-27.... What's the...

So I am trading some snowboard gear for an 89 RRC and need to chop it for a rallye (dirtballrally.com)... Once the race is over I want to keep the Rangie and turn it into a rock rig as my disco is to dear to me to not keep it as a DD. My disco is modded but still very streetable. The question...

Who's got some? The three inch springs aren't doing it for me any more, plus I have a new DD.

Reading through the Land Rover factory manual and it seems like some of the steps are a little retarded.....Honestly remove the fan shroud? Also it says to shift the CDL into neutural.....My T-vase is siezed and the CDl won't move, how important is this? Any shortcuts or help would be...

I haven't been able to even think about looking under my ride (side of the road in the desert hovering around 20degrees) yet so hopefully I don't sound to un-informed. 5 hours into my drive to Reno from Las Vegas my t-case started whining. I figured I could addres it later and kept on driving...

3" lift 98 DI Baaad vibes. Changed my u-joints today. The Vibes are considderably worse and I am totally lost. I marked the flanges both in reference to the T-case and rear pinion but my efforts to maintain the balance were futile. What the heck am I supposed to do now? Anyone Know of a...

Pics of the build. All metal was free scrap. Total cost a little over 100$ including paint.

Just got a used set of Piaa 580's. I want to wire them into the stock fog light wiring. I had some Hella's untill some jerk broke them off in a bar parkinjg lot. Hella's had two wires out of the back (pretty straight forward) the Piaa's have three?...Any suggestions would be helpfull. 98 DI