Search results

I have an 1995 RRC LWB (24 spline) and does not accommodate alloy wheels because of these HD half shaft axles. Changing the half shafts to accommodate alloy wheels so these are for sale. The half shafts have less than 6K miles on them and are made by Rover Tracks. These were purchased from GBR...

I have two transmissions available for sale both came from very low milage Land Rovers. LT77 5spd came off of a Defender has the shifter and bell housing. LT230 transfer case pictured is not included in the sale. Transmission is very tight and no slop on shifter. Suffix on Transmissions is "H"...

The vertical retro grilles are in. They are all one piece like the stock grille for installation. Note #3 and #4 from the top down are a three piece assembly. #2 from the top down has a 7" diameter inner lights designed around the Hella 500. #3 has a 5" diameter holes for ProComp 5" lights...

I have a DII rear air bag along with two height sensors and one valve block for the Eas system. $50 shipped

Hey guys I have many wheels available for sale. I have 3 sets of five ready to go. the tires are not included as they are miss matched an many of them are worn very bad they are not worth it. Price is $550 plus shipping for any set of 5. -18" Hurricanes Discovery II/Range Rover p38 -16"...

Does anyone here in the states have a set of Zu Wheels or Mach 5 on their DII? I need to get away from my 18" Prolines and fit a set of 16" wheels. I want to go with the zu wheels as I love their look and lightweight construction. Does anyone know where to get them here in the states? I've...

Does anyone here in the states have a set of Zu Wheels or Mach 5 on their DII? I need to get away from my 18" Prolines and fit a set of 16" wheels. I want to go with the zu wheels as I love their look and lightweight construction. Does anyone know where to get them here in the states? I've...

So I've had many problems with the DII since bought. It seems like the dealer which I bought it from messed with it to get it to sell. It had rough idling problems and all of those have be resolved with a complete headgasket kit replacement. O2 sensors changed and everything is up to par with...

I have Disco I CDL Lt 230 shifters with all components for addition to your Disco. $150.

I've decided to part out my '91 Classic: -3.9 Engine you may pull so I can show it works $450 -Transmission and transfer case (not lt230) $400 -ECU $60 -Master Cylinder $120 -Complete set of of transmission (4 hoses) to Radiator core lines Custom set of lines made out of Stainless steel braided...

Well, I ran into luck I found the shifter from an '04 but it did not come with the brackets that connect to the CDL. Does anyone by any chance have any spares? If not does anyone have one laying around from a CDL that they have not installed where they can scan it or trace it and mail or email...

I am getting frustrated and wondering if anyone has experienced this. After my headgasket kit replacement I have replaced the ACE pump, and both idler pulleys(they are both 80mm). Three new belts have been broken. The latest looks like it started to shread on the side closest to the engine...

I hate to see it go after so much work but I must now concentrate on new projects in my life. Pictures: http://albums.phanfare.com/4936703/2179152#imageID=31698915 91 RR Classic with much too much work to list but I will try to remember most of it: -Just got a new ABS pump installed last week...

...that is what happend here with my 01 DII SE7. I was on here with slight problems of my Disco idling at at stop. I was smelling a bit of coolant here and there. Coolant level drop over two weeks about a 1/4". I then decided to go for it. I ordered the gasket kit and replaced all the gaskets...

I have a complete kit of internal parts from a '93 RRC/DI ABS pump. I carried these with me during my trips in the case of a failure to my ABS. Believe me ABS pumps fail all the time. This is the Second ABS pump kit I have used in my trips. You never know when there will be a failure. The ABS...

My CD change is up for grabs. No magazine and coming off an 01 DII SE7. $50 bucks plus shipping. Located in Burbank.

I have a Black bumper for an '01 DII. $120 plus shipping. Located in Burbank, CA. It does not have the Headlights cleaners and the center lower valance has cool black mesh.

I just noticed today a hose to each axle in the front and rear. The hoses do not look to be original as they are being held with zip ties. The air hose is at the driver's side of the axle and they are located at the top. Is this stock or some kind of locker? I have read and some post about...

I am looking to downsize my power tank. I have a 15lbs tank and would like to trade locally for a 10lbs. Its been filled about a handful of times. I am located in Burbank, CA and would like to trade locally. Comes with boot.

Does anyone know much about this tech article? http://www.discoweb.org/cdlsolenoid/index.htm Does this mean that all Transfer cases have the locking capability? And therefore this is a way to lock it with an electronic solenoid? Or if someone want a CDL they would have to swap for an LT230...