Search results

Hello- 2002 P38. air fitting at reservoir is leaking. have replaced orings to to avail. Seems like to orings are not making a seal with the fitting. Anyone have experience with this? Can the fitting be replaced or do I have to look for a new to me reservoir? Tks- Joseph

Need one. Have lightstone interior, but will entertain other colors for the right price. Tks- Joseph

Need one! Tks- Joseph

Looking for a 2000-2002 drivers head light assembly. Tks- Joseph

Looking for a radio and subwoofer for a 2002 P38 with Nav. Joseph

Hello, My 2002 4.6 HSE with H/K and Navigation has an issue with sound. The left front and rear speakers don't work with the radio, but do work with the navi. When I turn the radio on, you can hear the faint white noise in the left speakers, but no sound. Since they work with the navi, I am...

Any thoughts for/against? Tks- Joseph

Hello, I am selling the distributor from my 1995 RRC. It has ~18months & 10,000 miles on the cap and rotor. It also has the wiring and bracket relocating the ignition module to the radiator area. You will need your gear and pump apparatus if using on a pre-serpentine model. It all worked...

Hello Everybody. I am looking at a 2002 P38 with an Airbag fault and Traction control fault. The truck has only been driven ~3500 miles in the last couple of years and there are 75k on it all together. Do you think this is something that I'll be chasing forever or relatively trivial fixes...

Anyone have a recommendation for a shop to do an inspection in the Patterson NJ area or Tacoma, Wa area? Joseph

Hello- I am looking for a 2000-02 P38. Anyone have leads? I am looking for relatively low miles <100k. Will accept suspension and ABS faults. tks- Joseph

Any ideas on why a P38 key-in alert would continue to sound after the key has been removed from the ignition? Tks- Joseph

I searched.....promise. 1995 LWB My back windows are a little hinky! If I release the window locks, they immediately roll down. The window switches have been cleaned, and the ECU doesn't have any tell-tale signs of a bad solder. Getting the windows back up is tricky. The switches work...

I have lifter noise at start-up. It doesn't happen every time I start the motor, but more often than not. Cold weather certainly makes it last a few rev's longer. I have the following: Crower 229 cam Crower cam-saver lifters new LR heads composite HG's OEM pushrods I use Rotella 15w40 oil...

I am trying to dial in my vacuum advance and mechanical advance. Anybody have the advance curve/specs for the lucas dizzy? This is for a 3.9/4.2. I know 8btdc at idle, and there seems to be a max of 33-36 advance? Tks- Joseph

I am looking for running boards for a LWB. tks- Joseph

A new timing set to replace the sheared cam sprocket teeth didn't do the trick. I stripped the engine down to the heads and about half of the pushrods are bent. Once I get the heads off and checked, I'll replace the rods, lifters and cam. Joseph

Check this out. The cheapest paint job yet!!! http://www.reseland.com/swap Too bad that less than a month later the cam and timing set took a crap. Now it is waiting for me to rebuild the motor. Joseph

The LWB is down!!! Fuel? - yes, plenty of it. Spark? - Yep, packs quite a punch, I might add. I swapped coils to no avail, swapped caps and rotor; also to no avail. (Firing order is verified correct) I have checked for compression and air does exit the spark plug hole during cranking. My...

Here's a starting question- I was at the library today for about 2.5 hours. When I went out to leave, I cranked the motor and it stumbled then quickly died. I continued to crank and there was an occasional hint of catching. First suspected the fuel pump, but I could smell raw fuel in the...