Search results

WTF? Dude, I have bought parts from you for years, without any problems and with great service. I have even recommended you to many other rover owners who have given you hundreds (if not thousands) in business. But recently I have called in search of a stripped GEMS 4.0 short block. I send...

Where do I start? Found a '99 D1 here locally that "seemed" to be a great deal. Went to check it out and was amazed at the condition of the vehicle. Black SE with practically no scratches, zero oxidation and the interior was near perfect (just some wear on the drivers seat). It has an ARB front...

My seats are shot and would like to replace them with a sweet deal I found on some D2 seats. But... Anyone tried replacing the rear seats on a D1 for D2? Any problems with the front seats? Just don't want to waste the gas or the time. Thanks!

Not mine, but looks tempting: http://miami.craigslist.org/brw/cto/1399030868.html 47k miles They are asking $16,500 The motor in the D1 is going out (long story), and trying to decide if I should rebuild a spare I have or buy newer truck. What do you think? Too bad its on the other side...

Hey guys, 97 D1 with 162k and the heater is acting up. If you let the vehicle run for a few minutes then drive you will get heat blowing but it shortly goes away every time. So basically heat for a few minutes, then it goes away and just blows room temp air. Any thoughts? Do I need a new...

I know this is a common problem, buy I have a 97 D1 with 163k that I've owned for 5 years. Starting last winter it would have rough starts in the morning. The oil pressure would act really low when its cold with excessive tapping. This would happen for between 30 sec to 4 minutes. Well...

Converted or not for a D1. If you know of someone, or a place to get em cheap! Thanks!

has anyone tried Bills combo? Also, do you need to put new spacers and bolts in order to place a vented rotor is the Disco 1? Thanks!

Anyone know where do get one? Getting pissed trying to find one through google. Thanks!

97 D1 Doing work on brakes and after reading several threads, I cant decide which to go with: 1. SLOTTED AND BLIND DRILLED EBC sport brake rotors in the front with current Brembo Pads (current pads) 2. DBA vented rotors with Brembo pads 3. D90 front caliper-rotor upgrade WHICH IS BEST...

Are they any good? Has anyone rebuilt thiers? thanks!

best place for new temp sensor? is there another manufacturer replacemen (GM, Ford, etc)?

1997 D1- lound "clank" sound comminf from the front passanger ball-joint. Usualy when making a turn on a gutter-driveway-etc. replicated when rocking the rover back and forth. SUGGESTIONS???

97 DI with 151k. replaced rotors with NAPA crap and the pads with Brambo. Since it stops worth crap (feels like my old 65 mustang w/out power assisted brakes!). Braking in fine when you first press the pedal, but it goes HARD the further you press it, with less braking. Feels like it just...

Hello! Just put in a new battery in my 97 disco which sat for 6 weeks with a dead one. Now it wont turn over? Good power throughout, but the security light by the tach and spedo stays solid. Does the security system disable starting? Kind of lost. Has a new starter. ANy ideas? Thanks!

Got a 97 D1 with one bad O2 sensor. Should I replace all four or just the one? Thanks!

Just thought I would give those who read: No codes. No check engine, and 3 SYSTEMS NOT READY! update: Yesterday I got in the car and drove to discover the ckech engine light was on. Yeah! I have not been able to determine what was causing 3 systems to show not ready without showing any...

Anyone have one or know where to get it new? Thanks!

97 Disco, 143k with 3 systems not ready on the emmissions. No codes, have put over 2,000 miles on it TO GET THE DANG THING TO RESET, and I am at a complete loss!!! The bugger expired back in Jan, and I have gone through all tempary reg. Not sure what else to do? Any suggestions??? Thanks!!!

Has anyone used the ARB Polyurethane panhard bushings? I was told that it doesnt make a difference with off roading for the PanHard. Does it? I plan on using the rubber for the rest of the vehicle. Good or bad idea? Thanks!