Search results

What: 75th birthday for Land Rover Who: all Land Rover clubs and owners Where: Greek Peak Mountain Resort When: June 14-18, 2023 Why: really? You are asking why??? more details: https://www.anarc.club/

Looks like the ANARC event really starts on Thursday morning. So I’d need to leave Wed. My son has a school test he can’t skip on Thursday morning and I’m looking for a seat for him Thursday afternoon from someone leaving/passing by the northern Virginia area -or- eventually that can meet him...

For posterity, the connector of the D1 (NAS? mine is a 1996 D1 NAS) audio amp is reference CET1809 on this website: https://connectorexperts.com/i-31643962-cet1809.html?ref=category:1458530 which was helpful finding a connector based on its pin (aka "cavities"). Now.... at $100, I'll be looking...

Looking for a D1 front winch bumper (not ARB, more streamlined/light design like a Safari Gard or similar look). Ideally for a body--lifted (2") truck, but I'll make the necessary modification(s) if needed.

I know some will say this is heresy and should not be done at this stage of the D1 area and how rare a 5-spd D1 is. Others will question even doing it. The decision was made a few months ago, this is is full reversible in my case and this thread will capture what was done and how so that you can...

Does anyone have first or second hand information to share regarding front and rear bumper options./pitfalls/etc for a D1 with a (2" in this case) body lift? I'm investigating the build vs buy route and before I start reaching out to vendors (for the buy part), I'd like to understand what has...

In the process of installing a 2" body lift on a 1996 D1 V8 (4.0L NAS/R380 5spd), I had to move the truck and could not engage reverse. The body mount bolts are not tightened at all (i.e. bolt through bushings/washers and that's all), so I do expect the body to come down a tad when it will be...

My ignition barrel assembly was sticking some time ago (many years ago). I took it apart, did whatever to fix it. did it again recently and I took it apart again. Now, this time I did not pay enough attention and I’m left with a single metal ball and I can’t figure out where it’s supposed to...

A few weeks ago, my '06 LR3 V6 started throwing a few codes but the sticky one was P0108. I also got, at the same time, a P0069 and/or a P0106. Looking online in various forums/posts, it appears that the atmospheric pressure sensor was dead/dying and needed replacing. It happens that this...

<please delete this thread, this was a link to eBay which is not acceptable per forum rules> <Sorry!>

Hi, This might be a long shot, but I'm looking for a driver-side catalytic converter (assembly?) for an '06 LR3 V6 4.0L. Thanks, Loic.

Ordered oxygen sensors for my 06 LR3 and got the wrong part. Got them from rock auto, I did not check any picture, so it's kind of on me (but I always assume on newer vehicles, the parts fit....). Anyway, if you are buying oxygen sensors, make sure you peak at the picture of the connector plugs...

What checking out what's involved, and the consensus seems to be: - replace oil between 50 and 80K miles (that's ZF recommendation; LR original recommendation was 150K miles) - go with the metal sump conversion to make it easier (no need to raise engine/transmission) If so, where did...

Apparently, these lights would have the right dimension for my small car project: PRC9916. They should be on the front of D1 and P38 (4.0 and 4.6) as repeater lights. I'd need two lights and the plugs from the wiring harness (plus some wiring so I can splice without issue! :) ). More details...

Hi, I need new bushing for the front lower control arms on a V6 '06 LR3. I've been reading about this a little but I can't get to a conclusion. What's the recommended path? I've read that changing the bushing is a pain (but then bushing are always a pain) and that it can be cost effective to...

Perfect shape (no rust) disco front and rear seat frames. Front seat are missing the bottom springs (easy to acquire or built). I still have the rear seat foams and they might be included in the sale (I've yet to confirm this). Price: free + shipping (I just hate to throw away good stuff)

Looking for a LR3 passenger side mirror assembly. Anyone know of any LR3 being parted out? Thanks!

This might be of interest for some of you: - front ARB-setup 3rd member (24-splines): http://washingtondc.craigslist.org/nva/pts/1582677420.html - rear ARB-setup 3rd member (24-splines): http://washingtondc.craigslist.org/nva/pts/1582757225.html

Cleaning up the garage, I'll let those go for free (or whatever they are worth to you: Rover parts, 6-pack, toys for the kids, etc.). Those came off rims I bought for the D90 a while go. They were stored on the rims for the longest time (I'd say ~3 years at least), got unmounted about a year ago...

Cleaning up the garage, I'll let those go for free (or whatever they are worth to you: Rover parts, 6-pack, toys for the kids, etc.). Those came off rims I bought for the D90 a while go. They were stored on the rims for the longest time (I'd say ~3 years at least), got unmounted about a year ago...