Search results

Rover Axle: Front stock pulled out of running Disco I for a D60 swap. Has about 100,000 miles on it. 3.54 gears turn tight. Cv joints are good as far as I know. $100 Dodge Dana 44 Front: Came out of a 1976 dodge powerwagon. Gears are I think 3.54. They turn tight. Pulled from the truck. I cut...

Question, Is the front timing cover of a 3.9L interchangeable with a 3.5L cover? Thanks.

2000 DiscoII leaks water into the cab on the floor boards when the air conditioning is running, the carpets are soaked both passenger and driver. Any Ideas on the problem and how to go about fixing it would be greatly appreciated. Thank-You

94 disco, has a 2 month old battery. I let the truck sit for a few hours, go to start it, and nothing, not even the interior lights go on. alternator was checked, and it is running strong. My other thoughts would be the fuel pump, as it has never been replaced 106,000 miles. I just don't know...

any used ignition switch for 94 Disco. Thanks

Does anyone know if they still offer these? Just wanted to check before I call. Thanks

I noticed that the Jeep Wrangler has hinged front and rear links. This seems to give really good articulation. The wrangler that I wheel with has really good front and rear articulation, and even better if he had the long arm kit. The front actually is way better than the land rover with...

Went to sedona yesterday and when turning the truck on, I can hear the fuel pump really good, I mean really good! That thing moans back their! I was wondering if this a sign of it needing to be replaced? Also, at a stoplight yesterday, the idle started to drop like it wanted to quit. Usually...

What are some possible ways to remove the centralizing peg? I have been struggling with it all morning, and it won't budge :mad: ! Any advice would be very helpful. Thank-you

Was wondering if the Arizona Land Rover club was active up here? Was thinking about joining the club, but can't drive all the way to tuscon or phoenix for the outings (college).

Before I post a wanted ad for a ujointed rear shaft, I wanted to know if I would need anything other than a complete shaft to change to a ujoint? I am trying to switch from a rotoflex to a ujoint, and wanted to possibly buy a used rear shaft with ujoint, college is keeping the budget real low...

Well, I just got the rover back from the shop today. It now has a new starter, ignition switch wiring, and a new TPS sensor. After sitting overnight, I go to start it and it doesn't seem to fire without blimping the throttle. when it does start, it runs really rough for a few seconds and then...

I have a DI, and it refuses to start. It turns over, but won't fire. sometimes it will almost start, but dies out. The spark plugs have spark, fuel filter was changed not to long ago, I checked the fuel pressure on the fuel rail and it read 31 psi, I can hear the buzzing noise from the fuel...

Hey Dwebbers, I was wondering if there was any AZLRO members in flagstaff? I will be attending NAU this fall, and am looking for any good trails out near flagstaff. I am also planning on becoming an AZLRO member. I am moving out from Delaware, so other than a few family visits, I am...

I am looking for two front 1" suspension spacers for a DI

1 like new DII drivers side fog light- $120+shipping 1 like new DI rear step, includes all mounting hardware- $200+shipping 2 almost new OME 761 front medium duty springs- $70+shipping 2 DI bumper end caps in great condition, includes bracket and orange lights- $20+shipping call Brian ford at...

I have a 94 DiscoI, and I think there might be a problem with the fuel system. The problem started while running the trails at the Uwharrie Safari. As I was climbing a hill, the rover all of a sudden lost power and quit. No matter how much gas I gave it, it still quit. I let it sit for a few...

Hello, I was wondering if it is safe to change brake lines without bleeding the braking system? If not, any instruction on how to do it would be very helpful! I have basic tools and I just bought the EE braided brake lines and am dying to install them...