Search results

Im looking for a straight tie rod to replace the one i have, which looks like its doing the wave. Its for 95 D1. Also need a passenger side window regulator for the same truck. thanks, Will Also I don't care about tie rod ends, i have new ones waiting to go in it.

One of the tie rod ends on my drag link is bad. It is the tie rod end that is located on the knuckle end, not the steering box end. I know one tie rod has a left hand thread, so I just wanted to figure out which thread I should order before I get the wrong one. Thanks Will

I had a hole in one of the metal a/c lines that went to the rear a/c. i took the line out and had the hole welded. I have all the tools to draw a vacuum on the system and recharge it, but im not sure if i need to add oil back into the system or if the old oil stayed in the compressor and can be...

Im looking for two manual front seats out of a D1 in decent shape. The bottom support band broke in both of mine. thanks, Will

I have a new in the box brake booster for a D1. Its a TRW I believe. I'm asking $285.00 plus shipping. thanks, Will

I have a set (4) of 2in spring spacers that came out of my disco 1 for sale. Still in good shape with hardware. They are from rovers north and i paid about $100 for them. Looking to get 60 plus shipping thanks, Will

preferably a 2in. Anybody got one sittin around they wanna get rid of?

I installed a new servo and master cylinder in my D1 and after install my brake pedal is slow to return back to its normal position. If i push the pedal down just a little bit and let off of it the brakes lights will stay on. I know about the self adjusting switch and have adjusted it. If i...

It ran fine before I changed the cap, rotor, and wires. After installing all the new stuff it ran really bad when hot, turned out to be a crack in the rotor button, replaced that and all was good. Recently I began to see that the tach would jump and fall a small amount while normally driving...

So after trying to figure out an easy way to remove, install my doors for offroading I decided to lighten and cut down a set of normal doors. After completely gutting them for weight I marked how low I wanted to cut them and then went at it with a grinder. My goal is to have a set of doors that...

Im looking for a good used set of front abs sensors for a 95 D1. thanks, Will

I know how to actually lift them off the hindges, but how do I disconnect the wires(I think there is 16)? The rear doors have plugs that you can just pull apart, is the front the same way? I know they are not meant to come off like other vehicals that will remain nameless, but there has to be a...

Im installing drilled and slotted rotors on my D1. The rotors have curved slots, that obviously identifies them as left and right. Which way should the slots face? thanks, Will

I know threads similar to this have been started and I have searched. After rear ending a minivan going 15 mph I realized it was time to fix my horrendous brakes. It's a 95 discovery with 31" MT/Rs and disabled abs. It is hard to lock the tires up in the rain and basically impossible if its...

Im in the middle of installing my 3" RTE lift and need to know what to torque the trailing arm nuts too (the large ones that mount to the frame bushings, as well as the smaller ones that mount to the axle). Also what is the proper torque for the large nut that holds the axle driveshaft flange...

I just got an RTE 3"Hd lift and am now getting ready to buy driveshafts. For the rear im converting the rotoflex to a u-joint. For the front I am unsure of what i need. I was planning on using the driveshaft out of D2. Will this work? i know I will need to change the output flange on the t-case...

Thought I would post up some pictures of my new rear bumper that i built. It's made from 3/16 and is held to the frame with 8 3/8x1-1/4 grade8 bolts. The built in tow points work really well and have pulled out a suburban buried to it's doors in mud wothout deforming the bumper. I made this...

Looking for everything to convert my 95 discovery's rotoflex to a u-joint. Shaft, flange, and spacer thanks, Will

The bearings in my A/C clutch are shot. It's making a lot of noise when you spin it by hand and even more when the engine is turning it. The A/C blows cold and the actual compressor is ok. Is there anyone who sells just the A/C Clutch? thanks, Will

Im looking into getting some sliders for my 95 discovery. i dont like the idea of sill mounted ones and the rockware's are the only ones that seem to mount off the frame. Does anyone have any pictures of them unistalled as well as installation pics. ive done a lot of searching and cant really...