Disco 1 parts $20 for anything left

[lordhelemt]

As you may have saw from my previous post I’m parting a 99 D1.

I’m about finished taking what I need and a few others have stopped by and grabbed some stuff but there are stl a bunch of good parts available.

All remaining parts are $20ea. I’m willing to ship anything that is easy to box. Located in Arlington VA

 

[lordhelemt]

For example

complete doors with cards, regulators, glass, etc. $20

Dash (no warping) $20

 

[El Ed]

For example

complete doors with cards, regulators, glass, etc. $20

Dash (no warping) $20

What color is the dash? Beige? Shipping to 92130? Thanks!

 

[lordhelemt]

Beige but I’m not sure how easy that will be to ship. I plan on pulling it later today/tomorrow. Once it’s out I’ll see if it can be easily packed.

 

[terryjm1]

If it doesn’t have rear air I would like to get the alpine window trim, the rear seat belt escutcheons that are in the side trim, the lower rear trim (both sides), and the fasteners for the front kick panel trim (both side - total of 4 fasteners (photo shows holes where they should be) . If the trim under the front seats is really nice I’d be in for that, too. Also, if you have the rear cargo cover that is also on my list.

The photos below should help. Shipping is going to be expensive, unfortunately. Before you go to any effort if you could send some photos that would be great.

 

[lordhelemt]

The front seat trim has a few cracks. They are okay but not perfect. Kick panels and rear cargo cover is gone.

Will snap pics of the alpine window trim and rear seat belt escutcheons tomorrow.

 

[lordhelemt]

What color is the dash? Beige? Shipping to 92130? Thanks!

Pulled the dash today but not sure how I could safely ship it as it is awkwardly balanced and a little heavy.

 

[terryjm1]

“Kick panels and rear cargo cover is gone.”

Any chance the fasteners are still hanging around for the kick panels?

 

[lordhelemt]

I don’t think so. I think the guy grabbed them when getting the panels

 

[robertf]

I need 2 sunroof nuts and both high and low horns.

Hows the grill?

 

[lordhelemt]

Grill was cracked so it was pitched early. I think the sunroof is aftermarket so I'm not sure if it has the nuts.

Both horns are available. Did you want to pick up or ship? If shipped pm me your address so I can get a shipping quote

 

[lordhelemt]

If it doesn’t have rear air I would like to get the alpine window trim, the rear seat belt escutcheons that are in the side trim, the lower rear trim (both sides), and the fasteners for the front kick panel trim (both side - total of 4 fasteners (photo shows holes where they should be) . If the trim under the front seats is really nice I’d be in for that, too. Also, if you have the rear cargo cover that is also on my list.

The photos below should help. Shipping is going to be expensive, unfortunately. Before you go to any effort if you could send some photos that would be great.

Here’s the alpine trim

how do you remove the rear belt things?

 

[terryjm1]

They look good, any sun browning? I cannot see the part that browns from sun damage very well. I need the fasteners as well, if they survived removal. On the seat belt retractor escutcheons, I believe if you take the c-pillar panel off they sort of slide out.

 

[terryjm1]

Does one key fit the ignition, driver door, gas tank door, and rear door?

 

[lordhelemt]

I didn’t notice any browning but there wasn’t great lighting. I’ll check closer tomorrow in the daylight

yes, the key fits the door/ignition/and fuel door but I’m keeping the ignition for now for the project.

I’ll see if I can get those clips out tomorrow

 

[terryjm1]

I didn’t notice any browning but there wasn’t great lighting. I’ll check closer tomorrow in the daylight

yes, the key fits the door/ignition/and fuel door but I’m keeping the ignition for now for the project.

I’ll see if I can get those clips out tomorrow

Thanks for your effort. I know this is tedious.

You can remove the ignition lock assembly from the switch pretty easily. Then you just turn the ignition switch with a screwdriver. The Disco ignition switch may well fit the lock cylinder of your project as well. I didn’t try it but it looked to me like the Disco switch would fit in the 110 lock cylinder I have, I will try next time I’m at my shop.

Regardless, I’m not in a hurry and it is more a want than a need. (1 key for all locks) If you save the rear cargo door lock assembly, driver and passenger door lock/handle assemblies, and gas tank door lock, whenever you get around to not needing the Disco ignition lock, I’d be interested.

EDIT - thinking on this more, this is a 99 and has the polished (not black) door handles, right? In that case I’d also be interested in the rear passenger handles as well.

 

[jessedriven]

If you're still parting:

Drivers door handle or lock plastic bits (stc1219)

Door Lock Cam Grey (Genuine) STC1219 Island 4x4 - Specialists in Land Rover and Range Rover Parts and accessories for all models. UK and worldwide mail order.

Door Lock Cam Grey (Genuine) STC1219 Land Rover parts, Land Rover spares, Range Rover parts and accessories for Freelander, Discovery, Defender and Series models. UK and worldwide mail order. Competitive prices.

www.island-4x4.co.uk

left pass window motor/button
left rear seat belt receiver

prob can think of some others!
Thanks!

 

[lordhelemt]

Apologies I should have updated this thread last week but the truck is gone