Cleaning out the Garage - Rover Parts

[woldd90]

Cleaning out the Garage?


1. ?97 Defender Transmission Cooler, about a year old, less than 3000 miles, paid $200+, asking - $125

2. ?97 Defender Front Drive Shaft ? Less than 4000 miles on New U-joints. - $75.00

3. ?97 Defender Rear Drive Shaft ? Less than 4000 miles on New U-joints. - $85.00

4. 97 Defender 4.0 Fan Clutch ? Used 46K miles - $100.00

5. Defender/Disco - New and unused 3.9 Fan Clutch ? Paid $200 asking $165.00


Range Rover Parts:

6. Range Rover 4.6 Transfer Case, low miles ? $575.00

7. Range Rover Mondial Wheels, set of 5 ? great condition $500.00 (Look Great on a Disco)

8. Range Rover Hurricane Wheels set of 4, some clear coat problems, one slightly out of round, all with Michelin tires 55% tread - With Tires $500.00, with out $250.00

9. Range Rover 4.6 EAS Valve Block, no o-rings but in good working order - $95.00

Offline email is swold@pbcx.com

 

[dbdisco]

Is the 4.6 transfer case faster than the 4.0?

 

[cptyarderho]

by at least .6

 

[WILL.TILLERY]

Its made to handle the extra .6 for lack of better explanations.

 

[cdmbrennan]

Scott,

do you have any idea if the front and rear driveshafts would work on a SIII?

Do you have measurements?

Thanks
Chris

 

[woldd90]

Chris, I will get you the measurements... I am pretty sure that the front would work without any modification, but the rear may be a tad too long. I will get them soon and post the numbers.

Thanks,

Scott

 

[woldd90]

Just to clear up the confusion... The 4.6 transfer case, transfers the power 40 percent faster. It is bullet proof and can save your life. If an improvised explosive device detonates under your truck, only a 4.6 transfer case can handle the explosion. Any garden variety 4.0 transfer case would be shredded by the explosion.

BTW, it is has a smooth glossy and polished Titanium finish instead of Aluminum and steel.

 

[cdmbrennan]

Hey Scott,

Is there a Greyhound shipping terminal near you that you'd be willing to ship from (www.shipgreyhound.com)? This usually is the cheapest way to send/receive things bulky like driveshafts. If there's any way you could get a shipping quote from them or UPS to St. Louis (63021- business address) I'd appreciate it.

I'm definitely interested in the front and poss. the rear as well- will wait for measurements from you.

Thanks again.

 

[woldd90]

Chris,

The Front Drive Shaft Fully compressed is 23 1/2 inches. It has about 2 1/2 inches of travel before the splines start showing. The rubber boot is intact and in good condition.

The Rear Drive Shaft Fully compressed is 27 inches. It also has about 2 1/2 inches of travel before the splines start showing. The rubber boot is also intact and in good condition.

Thank you very much,

Scott

 

[mightymg]

IS the rear driveshaft the same as a disco 1?? if so how much for shipping to Ut thanks alot.. Lane

 

[dbdisco]

The DI rear drive shaft is about 35 in.

 

[cdmbrennan]

Thanks Scott. I'll measure mine tonight and let you know if they'll work. Guess I could have done that today before waiting for your measurements, duh.

Okay to call dibs on both front and rear until tomorrow morning?

Chris Brennan

 

[woldd90]

Bump...

 

[mightymg]

driveshafts still available, if so are they the u joint style for the rear, and will it fit a d1. thanks alot. Lane

 

[woldd90]

I am pretty sure that the back DS might be a bit short. The disco is a few inches longer.

But, just in case... here are the measurements.

The Rear Drive Shaft Fully compressed is 27 inches. It also has about 2 1/2 inches of travel before the splines start showing. The rubber boot is also intact and in good condition.