Supercharger set up to 3.9

[budzny]

Anyone know 's that has supercharger set up to 3.9? I need to know where vacuum lines are hook up. Pictures are highly appreciated. Thanks

 

[Nomar]

Huh?
Nobody here has a supercharger...

 

[D Chapman]

Better call Steve Young.

 

[Colorado Scott]

Pomps in Denver has one set up on his RRC. Check out solihullsociety.org

I'm sure it's a bit different than yours but tracking down a few vacuum lines shouldn't be too difficult.

 

[budzny]

Thanks, Guys for the reply. Just installed the supercharger unit last Monday and been figuring out the vacuum line since then but was able to start the truck this afternoon without the rising rate regulator in placed. Tomorrow will install the regulator that has in/out piping and small piping in between. Oh, RRC set up are the same as my 94 d90 with 3.9 engine. 4.0 has different set up OBD2 MF2 (micro fuel system) and 3.9 OBD1 has RRR (rising rate regulator).

 

[Discoinjapan]

Bud,
You should do a write up on this, with lots o pics!


Mike

 

[budzny]

Mike,

Pictures soon and also installed hedman hedders from you with new magnaflow cats and flowmaster from Randy. Bringing sexy back, man..

Sal

 

[Jupiter Rover]

Did you use an Eaton?

 

[Discoinjapan]

Mike,

Pictures soon and also installed hedman hedders from you with new magnaflow cats and flowmaster from Randy. Bringing sexy back, man..

Sal

COOL! Lets see them pics!

 

[gmookher]

This I wanna see!

 

[dmarchand]

Did you use an Eaton?

Rimmer was the only company that made the SC for the 4.0 from what I recall (ancient history). But who knows.

Some legacy discussion:

http://www.d-90.com/faq/Engine/EngTurbo.html#Autorotor

I know a few east coast d-90's with one.

 

[Discoinjapan]

Rimmer was the only company that made the SC for the 4.0 from what I recall (ancient history). But who knows.

Some legacy discussion:

http://www.d-90.com/faq/Engine/EngTurbo.html#Autorotor

I know a few east coast d-90's with one.

To be honest; its all in who you know!!

 

[Jupiter Rover]

Rimmer was the only company that made the SC for the 4.0 from what I recall (ancient history). But who knows.

Some legacy discussion:

http://www.d-90.com/faq/Engine/EngTurbo.html#Autorotor

I know a few east coast d-90's with one.

Thanks. Let us know how everything turns out.

 

[ptschram]

Rimmer was the only company that made the SC for the 4.0 from what I recall (ancient history). But who knows.

Some legacy discussion:

http://www.d-90.com/faq/Engine/EngTurbo.html#Autorotor

I know a few east coast d-90's with one.

I have one off of a Cameron Concepts 4.6...

 

[Ron]

Remember to put oil in it.

Ron

 

[crown14]

I have always been, am still are, under the impression that these just are not good engines for S/C.

 

[gmookher]

I have always been, am still are, under the impression that these just are not good engines for S/C.

I agreed. Forced induction needs to be incorporated from the design up. These heads, valvetrains, blocks and sleeves are poor candidiates IMHO

 

[budzny]

Magnuson M62

Did you use an Eaton?

 

[budzny]

GM SC oil cost 11.50 for 1 bottle.

Remember to put oil in it.

Ron

 

[budzny]

Trying to install the RRR but I need a gauge before doing anything and was so sleepy to take pictures as I work nights.

Sal

Thanks. Let us know how everything turns out.