Search results

I am rebuilding my rear driveshaft. I need to know what centering ball to order for the double cardon joint. Does anyone know the part number?

I have code P0455. I have replaced purge valve, gas cap, inspected all the lines, and smoke tested the system and can't find anything. Any ideas? I wouldn't care, but I have to pass emissions here in Atlanta.

I have a complete setup from a parts truck. The springs are front RR 4-1 and rear RR 1-2. The shocks are typical OME shocks in good shape. $300 shipped.

Let me know what you need. Parting out 2001 Disco. Engine runs, but the ECU and wire harnesses are no good. Rear steel bumper (basically new)- SOLD 265/75r16 Nitto Ridge Grapplers (less than 100 miles on them) on Rover alloys - $1000 Interior is in good shape, if you need any bits make an...

I am getting p0452 (fuel tank pressure sensor) fault on my D2. I cannot for the life of me figure our why. I tried installing a spare fuel pump I have (sensor is built into pump) and still getting the code. Nanocom reads as follows: P0452 occurs during drive cylce c signal too high I can clear...

Long story short I did a body swap from an 01 to 03 disco after a rollover. Everything is done and the truck is running great. However... I have a small issue. The harness from the new body does not have a plug for the Canister Vent Solenoid (I assume because my engine and ecu are non-SAI and...

Anyone have any laying around?

Hey everyone. My D2 is having a security issue. I have to hit the unlock on the fob every time i try and start the truck. If I don't I get the solid red security light and no crank. I have cleared all security codes and all unused PLIPS in the computer. What could be causing this?

I'm working on a friends d2. Engine does turn over. no spark. no fuel pump. I can't communicate with the ECU. I CAN communicate with the BCU and other computers. Just not the ECU. M and S lights are flashing. I have checked harnesses and everything seems to be fine. Any ideas? I have tried...

I have a great set of almost new Arnott front air struts for a 10-14 RRS. I originally mistakenly listed these as LR3 fronts, but after checking the part number they are for RRS. (I do part time work at a Land Rover shop so everything runs together) They have very low mileage and were taken off...

Looking for a working D2 key fob. I just need the "electronics" from inside the key. Anyone have an old D2 key they don't need anymore?

So...my truck and everything was running and working just fine, but now it won't crank. I turn the key and nothing happens. The security LED on the dash is solid and NOT flashing. Almost everything I have read says when the truck is immobilized it will flash. What does a solid light indicate? I...

sold

I am about to "reinstall" my Rovertym sliders (circa 2002) on my truck (new body so the holes aren't drilled yet). What size were the rivnuts used in the original install kit? 3/8"?

I am finishing up the last of my D2 body swap. I have all the interior bits back together and everything is working as it should EXCEPT the windows. They will not roll down. When i push the switch I hear the relay behind the glovebox clicking. I have also checked all the fuses and everything...

SOLD I have a rear door ladder for a Disco (D1 or D2) for sale. It has the common powder coat flaking problem, but that is easily fixed with a wire brush and a rattle can. $50 plush shipping.

Random question...I am rebuilding my trail rig. Is the radiator fan shroud absolutely necessary? I know it probably helps with directing air over the engine, but it sure would free up a lot of space in front of the engine to just leave it out. Thoughts?

I am working on a friend of mine's D2. It has sat for 5 months and we put a new battery in and it will not crank. Turns over just fine...just doesn't start. There is no spark. Here is what I have done already. 1. replaced crankshaft sensor 2. checked fuel pump and its running 3. checked all...

I have a Defender ARB Bullbar (non-winch) to sell. It is in good shape. Has been repainted. Located in the Atlanta area. asking $650

I am going to dive in to changing the AC compressor on a 2004 Range Rover (BMW engine). Any tips or tricks to make the job easier?