Search results

Hello all, How do you remove the steering shaft ujoint (closest to the box) Will it slide up far enough to clear the input shaft of the steering box? It is late and I just don't want to experiment at this point!! Thanks in advance..............it has been a long day of of nursing the old trucks...

aa

1974 dodge dart...........slant 6 and landau roof........8 track cassette and fm convertor....wow, that takes me back!!!

Will Tillery........do a search..........

I have the one from Rovers North with the extension. I never used it.......long story!! So, there is nothing wrong with it, basically brand new. I paid like $90 for it. If you want it I'd like to get $50 for it and I will donate $10 back to the BBS......let me know.

Good morning to all, I need some help!!! My clutch fell off of my a/c compressor last night. I found it laying in the driveway this morning. I can't find the bolt that attaches it. I noticed that the clutch has a threaded hole it and I was wondering if the attaching bolt was a special bolt which...

Thanks for all of the replies............It ended up being the rear u-joint on the rear prop shaft..........Couldn't detect it until I removed the prop shaft........ Special thanks to Paul Grant........great guy and offered some great advice. Called me and walked me through some options if I...

same noise not matter what.

bump for any other thoughts on troubleshooting before I rip this thing out.... If I put the front shaft back in and remove the rear shaft will this tell me anything? Just trying to minimize the time under the truck!!

no and no...............

Hello all, (98 D1 205,500 miles) Thought I had a bad u-joint (wish I had a bad u-joint), but upon further investigation I've found the problem to be "something" in the transfer case. Here's the story.... -bad vibration pretty much any speed over 20 mph -terrible metalic noise when coming...

Thanks for the replies.....................I rebuit the fuel pump several months ago and upon removal of the pump yesterday I discovered that the hose coming out of the pump had popped off..................it was engaged just enough to move fuel, but under no pressure!! Back up and running...

Hello all, I'm underneath the truck troubleshooting a no start issue and have a couple of questions......hoping to get her fixed by the morning...... -took my son to the school bus this morning and the truck started and ran for about 30 seconds and died. Wouldn't start afterwards. -The fuel...

Call me. I live in East Haddam and can give you a hand if necessary.........860-301-0855.

My saga continues.........I replaced the pump (which was bad, only producing 18psi at the rail), but my initial problem still exsists......the pump will only run while hot wired. Here is the frustrating part.....I have 12v at the connector pins for the pump and 5 volts on the two pins for the...

okay..........hopefully my last question regarding my fuel pump dilema...... Will the Airtex E3270 pump work in lieu of the Master E3270 pump when performing the pump rebuild that boulderbear so graciously outlined in a previous post.... thanks in advance for the help.........

I agree with your theory, but is there a way to check the pump with a multimeter to kinda prove out the theory? I am driving around now with the external power source hooked to the pump and I am going to change the pump tomorrow, but curiosity is getting the best of me..........thanks for the...

Thanks, Pete.............I assume you mean do a rebuild with a new motor....... The only thing that bothers me is that I can make the pump work with an external 12v supply....... I am getting ready to jumper the plug on the harness to the pump.......maybe I have an issue with the harness...

Relay in the footwell???? It is a 98 D1........I thought that the only relay was the mutifunction relay under the bonnet????

Thanks for the pump contact, but...................... I still need some help and here is the data from my latest troubleshooting which makes no sense to me: -I am getting 12v at the harness connector -I put 12v to the pump (with an external power supply) and the pump works -I hook the...