Search results

FS A pair of Range Rover Classic TWR rocker panels. Very rare. Epsom green off a factory 1995 truck. Used the bumpers on a LWB and rockers are too short. Only fit SWB trucks. $200 for the pair plus shipping. Doylestown, PA

Looking for a pair of TWR bumpers for a Range Rover Classic. Doylestown, PA

No interior lights by opening a door or using the interior light switch. Getting 12 volts at the dome light but I guess no ground. Was having some strange switch behavior, open passsenger door and rear windscreen heater comes on and real faint door warning chimes. Replaced the fuse box under...

delete

http://landroverforums.com/forum/private-sale-trade-classifieds-20/f-s-1995-rrc-lwb-sorrel-brown-front-seats-78522/#post561183 Recently purchased these front seats from Paul Grant. They are still at his shop in Connecticutt. Since purchasing them I have found a set of lightstone seats...

Front bumper includes end caps and all washer stuff except one nozzle. Nice shape no pitting of chrome. Doesn't include rubber crush can covers. $100 Brush bar includes removeable protectors for headlights. Some peeling of powder coat near mounting points. $100 Prefer to not mail the brush...

ABS light is on. Tried the paper clip and removed the ABS warning light relay, blue base on 95 classics, but I don't get any blinking codes. The ABS light stays on and doesn't blink. Does that mean there aren't any stored codes? If so why is the ABS light staying on?

Need the piece in tan that has the window for accessing under the front of the seat.

Factory brush bar off 95 Classic. Includes the removeable headlight guards. Great shape. $300 or trade for upper rear tailgate for same. Doylestown, PA

ABS pump not running. If I disconnect the 12 volt terminal and apply twelve volts directly to the pump it works. I'm also getting 12 volts to the pump on the other side of the terminal. ? I can hear the relay under the seat when I turn the ignition.

Looking for an original paint, hopefully, hood and cowl piece not too far from Philadelphia.

Looking at a truck that has been sitting for 10 years. Should internal engine corrosion be a major concern? Any easy to check red flags?

when line boring the cam bearings in a v8 block do the main bearing caps need to be torqued?

I have four BFG 265 75 16 KM1's mounted on early round five spoke D2 or P38 rims. I also have a fifth rim for a spare. Tires are 9,8,8 and 7 tread depth. Not at all torn up mild offroad use. I don't use them enough to justify the space they occupy. They weigh a ton so shipping would...

Not a bad dual purpose vehicle:http://www.youtube.com/watch?v=7V8uSplGroo

Clearing out the garage. Complete manifold with all sensors, fuel rail and fuel injectors. Came off a late 90's Range Rover engine that I converted to Bosch. About 90K on engine. Great deal $50.00 plus shipping from Doylestown, PA.

I need to replace the rear pinion seal on an 01 P38. Do a search and the only listings I find are an assembly including the yoke the driveshaft bolts to. WTF. Does the seal cut a grove on the yoke rendering it useless? Couldn't one not press the seal in all the way so it rode on a fresh spot...

P38 factory brush bar, winch tray & Hella lamps Factory original parts off 01 RR. All bolts and brackets included for mounting on your truck. Large working Hella 400 lamps mounted on factory bar with with white plastic lens protectors. Also throwing in an original winch tray for a P38. I...

Need 1 but would take a pair in nice to new condition. Preferably within driving distance of Phila to save shipping.

Need four 16 inch wheels. The rattier and cheaper the better. Just need to be round and able to hold air. Hopefully from the surrounding Phila. area so no shipping is necessary. Fred