Search results

After trying to decide between an LR4, a GX, LX, LC, D1, and D2 to replace my RRSC once it gets totaled out I think we have decided on another 04D2. My wife and I both loved our last 04D2 (had it almost 13 years), so I think we are going back to one. (an 03 might work too) Want something with...

Is there any way to check a VIN to see what service and maintenance has been done to a vehicle? Looking at another RRSC or LR4 and want to make sure the timing chains and other known issues have been taken care of. Thanks,

Looking at the possibility of replacing my RRSC (assuming it gets totaled out) with a 10 - 12 LR4. Criteria is that the timing chains have been done semi-recently. What else should I look into? I know the usual issues with lower control arm bushings. Thanks

I got t-boned today on my way to work. The other vehicle hit me right on the passengers side wheel, and proceeded to scrape down the entire passenger side. I'm not too worried about the cosmetic damage, I am more worried about what kind of damage may have been done to the front...

I'm getting ready to do the valve cover gaskets on my 10 SC and I am looking to get as comprehensive a list of parts as possible so hopefully I can have everything I need (minus something I break in the process) readily available. Right now this is what I am looking at: Valve cover gasket set...

Don't know if you all have seen this. 21K miles, for $48,800 https://copleymotorcars.com/?showroom=1995-land-rover-discovery

We are seriously considering buying a diesel disco and want to find out some info from someone who has experience with them. Looking at the DEF requirement, namely how much of a pain in the ass is it to keep it topped up, and can you fill it yourself or do you have to take it to the dealer to...

Looking at a disco 5, vin# SALRRBBK5HA038622 Thanks.

Hi, trying to figure out a new issue with my lr3. 132k on the clock. It’s developed a wobble while breaking, but only around 50mph and only for the very first second or so and then it soothes out. It doesn’t feel like the rotors as it isn’t constant. Any ideas? Thanks

A pillar airbag cover material is coming off, not sure what to do with them. Can you take them off without a danger of the airbag going off or damaging them? Anyone delt with this yet? Thanks.

Ive read about it but never seen it done. Can you safely use a rear spring isolator top and bottom on the rear springs of a D2? I need about 1/2 inch to even my truck out and dont want to put a 1in spring spacer on it if i can avoid it. Thanks,

I need to recover the drivers seat bottom on mine, its getting tatty and worn. I thought Exmoore Trim had recovering kits for a D2, but only have the cushions. (which are way cheaper on amazon than at RN) Does anyone know of a place that sells recovering kits for a D2? Thanks,

Looking at putting in some OME springs on the D2. Im running a 9.5ti winch in a tactical rover bumper (full bush guard). Im thinking the XHD for the front because of the weight, or will this be too much spring and i should use an HD instead? I dont want to run XHD or HD in the rear, i rarely...

Ive had the cooper LTZ's and GY Duratrac's on it in 19in, but now have 18 in tires. The pirellis that came with it are good in the dry, but on our way home from Wilmington today in a moderate downpour the truck skipped a few times in standing water. Never had that happen with the other tires...

Hi, trying to do some research on why I haven't had too many hits on this and am looking for constructive criticism. I am going to assume off the bat that the price is too high, however it might be that no one here is in the market for this kind of project, or that it seems like too daunting of...

So the captive nuts seized and I cant get the screws out, getting a new plate in the mail so i need a new one. Let me know what you have, new preferred. Thanks.

Anyone have a line on a large tract of land between the URE area and Wilmington NC? If so, PM me please. Thanks,

I have finally come to the conclusion that I will most likely never get around to finishing this project and I can use the garage space and money elsewhere. Located in Holly Ridge, NC. Asking $7000 OBRO, its posted on CL also. IT DOES NOT CURRENTLY RUN however +/-90% of the parts are there...

http://www.jensen-sales.com/chieftain/ Haven't seen a price point, but think its going to be the opposite of cheap....

Anyone have a line on a new seat heating element for the drivers side of a LR3?