Search results

located in North Bay p1b8g5 CANADA I have a lt230 from a RRC with shiftr. $200 I can email pics! JC

Hello, I'm looking for 1 FRONT wiper linkage for a '91 RRC. I believe '87 to 95 uses the same linkage. I'll take the motor too if I have too. The spindles must rotate freely!!!(the part that the wiper arm attaches to.) Please verify by taking the clip off. It is very difficult to rotate if...

you have to pry the tank to the driver's side while pulling down at the same time. It's a a tight fit!!!! ( disconnect as many lines as you can, bring it down a little disconnect lines, then lower. I had to cut the ruubber lines and replace once they were accessible!) I hope you took out as...

Done thanks to Oscar!!!

Done, thanks to Oscar!!!

yes please!!! As detailed as you can. ( the stock stereo!!!) Please post here or pm for email!! much appreciated!!! JC

Thought I would try a different angle, plus I'm computer illiterate and can't edit my other post!!!) Anybody got there dash apart??? Could you take a pic of the wires going into the stock radio?!? Thanks, I don't want to screw this up!!! JC

hello, while I was working on the console/dash of my '91 RRC I managed to pull two small wires out of their plug. I'm not sure which side to put them back into.( The wires are out of the plug and I got the leads out of the plug just not sure which side!!!!) The plug is a small and gray. one...

Thanks for replies, I found some.

Looking for cv ( double cardan) front driveshaft. One that will bolt up to lt230 front flange. Aftermarket is ok too.

Hey Aaron!! I couldn't pass up a winch discussion. My experiences include my X8000i (Jeep), HS9500i(RRC) a few 8274s( Jeeps) not mine but used lots!! And a good wheeling buddy that had the MM hydraulic (Jeep) Don't get the MM SUPER-Slow I mean you will get out but it barely looks like the...

Hello, Did Rover put different color intreiors in the DI?? What colors are a available. (I'm actually looking for a brown shifter boot for the tcase swap, but everyone seems to have black!!!) Any help is appreciated JC

looking for shifter and boot for D1 must be brown interior!! ( I think D1 came with brown console???? J

Ah, c'mon man! Check the obvious stuff!!!! Is there enough fluid in the ******. autos don't work well with not enough fluid. Try putting it in R or low range, do the fuse thing. Is the ****** engaging, is the tcase engaging? Look for obvious stuff. MAKE SURE IT IS IN GEAR BEFORE YOU WASTE...

Hello, Could someone tell me what the high ratio is in a '95 disco lt230. (I have an '87 from a RRC and it says 1.222 so I would like to know if it changed ove rthe years.) This is for a swap in a RRC with BW so I would like to do the math and figure out the difference if there is any!!!) J

Well, I've actually got two cases one froma '87RRC and one from a '95 Disco. The 87 i' m using as my guinea pig/parts one the '95 will go into is a '91 with BW. The light I was talking about is the CDL light. ( I might try to wire this up as I'm trying to do the 2wd conversion to the LT. Then...

Thanks, Ok, so take out the lockout solenoid. ( Does it seperate from the base plate??) The wires right beside it are for the alarm I presume.(Splice those to each other from the frame, are the wires/plug the same from BW to LT?)I should just be able to pull the "sensor" and fill with bolt+RTV...

Ok, after reading several pages I'm still confused!!!! What wires(solenoid) need to be plugged to make the lt 230 swap work in a RRC??? I undertsand the solenoid thing but some pics would definately clear things up. Are you suppose to loop the wires back to each other???? Only the alarm...

Looking for Disco 1 transfer case boot and knob. MUST BE BROWN and NO tears!! Thanks J

Check your email, I'm finally ready, sorry for the delay! :cool: