Search results

Doing some cleaning found some smaller misc parts for my old DII. 4 sets of poly bushings for 7100s 12mm ID Misc shock spacers 8 DI/DII binacle switches with pig tails. DII MAF 2 DII gutter mount brackets. Bought on here long ago, was going to make a light bar mount. 4 weld on...

Hello, I am selling two Safari Gard weld on diff guards. These were on my DII but I changed both axle housings and took these off the old ones. The remaining welds could be ground down and then clean up the guards with a wire wheel or sandblaster. The one on the front has been notched to clear...

Hello, I?m looking for an Oxford blue grill for a DII pre-2003. Thank you, Nick

Hello, I have 4 shocks and 3 hella 4000s off my DII. Shocks are in kind of rough shape, surface rust and a couple bad ends. 2 EA Bilstein 7100 12? Short Body Remote Res. One is in worse shape than the other. Valved 360/80. SOLD 2 EA Fox 2? Remote Res 10? travel. Don?t remember the valving...

I'm finally getting around to re-seal the trans case, however I'm not sure the best route to go to a: remove it; b: rebuild it; and c: avoid long downtime of the truck. I am leaning towards getting a second one, taking my time going through it 100% then swapping them. That way I can still use...

Hello, I am looking for the plastic shroud/guard that goes over the A.C. compressor on a DII. Thanks, Nick

Looking to see if anyone is located around there who would have a lead or info on a locating a DII AC Compressor. Long story short, a buddy of mine is driving a DII across country and the AC clutch bearings went out and is currently stuck there. Any leads on a local replacement or shop...

Looking for the crank, rods, pistons from a 4.6 to convert my 4.0 DII. Please let me know if you have 4.6 for this. Thanks, Nick

I have a pair of beige cup holders for sale. They are missing the inserts, but in good shape otherwise. They don't have the mounting screws but they are the same little black screws that LR uses all over the interior. $45 shipped for the pair. Thanks, Nick

I have a Terrafirma adjustable Panhard Rod that is for a DI. I bought it a few years ago, realized it was for a DI, tried to fit DII bushings in, put DI bushings back in, then gave up and let it sit there. It is the same one from Rovers North...

I found a Husky 8 for a pretty good price and would like to get it and install on my RTE bumper on my DII. I cant seem to locate the mounting hole pattern or any mounting specific instructions for that matter. The owners manual that I found wasn't very helpful. Will this fit in the...

Hello, I am looking for a cdl linkage to add to my DII. Thanks, Nick

I need a new starter for my DII. I remember reading about a gear reduction high torque one but can't remember the name of it or who makes it. If anyone could help me remember I would appreciate it, or recommend a different one. Thanks

I need to remove part of the drivers side carpet in the foot-well in my DII to fix a small rust spot. Ive never pulled the carpet there before so dont know whats involved to get access to it. Do I need to pull the seat and the center console as well to get enough room to weld in there...

Hello, I'm looking for left and right rear hubs with abs sensor for my DII. Thanks, Nick

The brake tubes running on top of the frame rail ruptured the other day. Currently my best guess it was caused by rust. I'm thinking about replacing them but just using two long lengths of braided stainless hose. Wouldn't have to worry about rust and they would be easy to feed back through...

Does anyone remember what the springs rates are for the 2" HD rear springs. I think they are they RR2-1, but I can't remember and the gray powder coat flaked off. They used to have them listed on their old site but not anymore. I'm trying to decide if I should stay with them or switch to the...

I am trying something out on my DII and I am looking for some dislocation cones. These are for the rear of a DII. If you have some for the front I might be interested in them as well. Thanks, Nick

Hello, Does anyone have a pair of stock DII rear shocks lying around? I want to re-valve my current shocks and need something to use for a couple days in their place. Thanks, Nick

I have eight (8) 1/2" to 13mm step down spacers for Bilstein shocks. These are for the 7100 shocks to be used on the stock mounting bolts so you wont have to re-drill and tap the stock mounts for a 1/2" bolt. 8 is enough to install 2 shocks as you need 4 per shock. Also they also function...