Search results

Sold my DII - don't need my Amigo. $120 US into my paypal account gets you the Amigo shipped ground in Continental US/Canda via the postal service. It will ship securely wrapped and in a plastic mouth guard holder (cleaned and sanitized). Only DII owners need apply. More info available here...

These are located in Toronto area. I am willing to drop off in Bradford PA area but these would not be an economical shipping item. I am selling the following set of 4 tires. They are Hankook Dynamic MT mud terrains size LT 225/75R16. They are mounted on AB black steel Land Rover Discovery II...

Looking for new or used D2 rims but only 7" wide. Thanks Len

I bought the 1st Overland replica models which arrived this past week. They are very nice and come in a cheap case. Here is a link to some iphone photos I took: http://gallery.me.com/lcater#100189 They are the 1:43rd Oxford Automobile Company Model - 43SET29 at www.oxforddiecast.co.uk. They...

Any coin holder to replace the cigarette holder. We've got bog a$$ loonies and toonies that need the space. Shipping to Toronto area. Thanks Len

Looking for: - rear tire carrier with LR logo and Lion (one on ebay but doesn't ship to Canada) - full set of black rubber floor mats Shipping to Toronto area. Thanks Len

Looking for: - rear tire carrier with LR logo and Lion (one on ebay but doesn't ship to Canada) - full set of black rubber floor mats Shipping to Toronto area. Thanks Len

Looking for a replacement left hand (driver side) for a NAS 90 1997. If U.S. based I will arrange shipment to Rochester for pickup. Thanks Len

Has anyone successfully hooked up a navigation/GPS system using the VSS feed on a NAS edition? Looking at a system for a '97 D90. Thanks

Well that's what the headline says. Heck of a mod! http://www.trader.ca/Search/Details.asp?mknm=806&Region=-1&subcategory=201&UID=56D5C77613954FE49159AE99131C39A7&CAT=2&ADID=7035731&ADS=7035731%7C Oh yea, includes a snorkel!

I can't believe no one has commented on this board about Steve stepping down from his NA Editor position for Landrover Monthly! I got my mag yesterday and it's a standout article.

My pto winch (Bamford) is leaking her oil and instead of tearing it down, I was wondering if the one shot grease/oil tube for the swivels would be a suitable replacement? The oil goes into the housing on the left of the photo. Inside this housing is the gear mechanism for engaging the free...

I am looking at swapping my old 2.25 petrol for a stock standard 2.5l diesel. Anyone have a frameless with running engine they are looking at selling? It's for my trail rig, so I am not interested in 200/300tdi as the cost is more than I plan to spend. She's just a nice old Series III looking to...

I am planning on putting a locker (true trac type) in the rear diff of my SIII. My question is this. How will it perform? There is no centre diff on a series so if you lose traction in the rear won't all the power transfer to the front? And hence make a rear locker useless on it's own. Or is...

I was towing my siii on a dolly which I do on a regular basis. I load the front wheel on the dolly while she is in 2H so there is no binding on the wheel. I then put transfer case in neutral, and the gear shift in 4th (the prescribed method by LR). I then test to ensure I get free wheeling on...

Has anyone installed a flexible clutch pipe from the master cylinder to the slave? I am installing a PTO winch and the rigid pipe is fouling with the drive shaft from it. Before I go start bending a pipe in situ I am hoping there is a flex pipe alternative. Thanks

I am planning on mounting a RAM mount on the coin try on the top dash of a DII. I tried some wood screws but they were not deep to pentrate the padded material. I don't want to go too deep on this one, so what have others used to secure items to the soft dash? Tks L

Looking for sliders for my SIII swb. I am located in Toronto area, so something north of the 49th or within 5 hour drive time preferred. Thanks