Hello.
I have a full RTE 5" lift for an 03-04 Disco. Never installed in original crate.
Includes:
RR4-3P Progressive 3" front coil
RR1-3 Rear Spring
BLS2F Front Series II Brake Lines
BLS2R Rear Series II Brake Lines
RSR Rear Upper and Lower Spring Retainer Set
PHDEX Adjustable Panhard...
03-04 kit. Never installed. Still in original crate.
http://www.rte-fab.com/products?page=shop.product_details&flypage=yagendoo_VaMazing_zoom1.tpl&product_id=77&category_id=13
Located in Western Canada. Will ship. Open to offers.
Cheers...
Looking to replace a cracked dash center fascia with a new replacement. Microcat lists my current fascia as AWR1383PUY. I can find AWR1383LNF replacements but they are listed as Ash Grey. The pictures seem to indicate that the Ash Grey looks identical to my black (PUY) part number. Does anyone...
Anyone out there running close to a 5 inch lift on a D2?
I'm looking for length measurements, pinion angles for the front and rear driveshafts. I don't have my lift yet it's on order from RTE. I've ordered the RTE 4 inch lift with 1 inch spacers. Looking to pick up the props and have them in...
A while back my drivers side headlight blew out and took the fuse with it. Around that time my DRLs started failing as well. Intermittent at first then gone completely. As per the RAVE documentation below I've checked fuse 13 in the engine compartment and fuses 3 and 22 in the passenger...
Hi all,
My drivers side heated seat stopped working a while back. Thought for sure it was a blown element but my local service guy seems to think if the light in the button stays lit it is something else. Is this the case? If I had a blown element would the light in the button turn off when...
Hi all,
Does anyone have experience with Piedmont Rover Parts? Looking for a bunch of stuff and they seem to carry it all.
Looking to determine if 'good shape', 'like new' and 'tried and tested' translates to reality in this case.
Thanks.
Looking for a bunch of little things to make the 03 fully operational once again. Would like to do a complete package to keep shipping down but will buy piecemeal if necessary.
Parts wanted:
03-04 DII Taillights that show minimum wear have no cracks and do not fill with water like my current...
Hi all,
I've done some searching and reading but have yet to find a definitive answer. Can anyone tell me if the front and rear door bass speakers are 6.5inch(165mm) standard drivers in an 03 Disco II?
Are the subs in the rear cargo area standard 6.5inch drivers as well?
I understand that...
I've seen some pictures of what seems to be D2s wearing the Pro Comp Street Lock Steelies but can not find a 16 inch 5x120 or 5x4.75 wheel available on their web site. Can anyone confirm a 5x120 PCD is available? Any pictures?
Thanks.
Just finished wiring up the Disco II with a powered tailight converter. Ran the power for the converter off the purple constant power lead in the factory trailer plug. Does anyone know what the constant power lead in the trailer plug harness is supposed to be used for? It is the purple wire, top...
Finally recorded my 03 engine knock. Actually took two recordings. One when the engine is stone cold and one when it has been warm for 15 minutes or so. Took same route at same speed both times. My drive way is slightly up hill. In the audio you'll hear the knocking more prominently when I'm...
Just put back together the 4.6. New timing gears/chain, front cover, oil pump, water pump, thermostat, serp belt, plugs etc. When the motor was apart had a good look at the rod bearings and they looked fine. Fired motor back up and 'yippee'...still have a bad engine knock when the motor is...
Tired to find the RN11YCC plugs the RAVE calls for in my 03 4.6. No luck anywhere. Closest I could find was the RN11YC4 plugs. Looked in the Champion book and they recommend the RC12MC4 plug for the 4.6 motors. Isn't this a colder plug then the RN11YCC?
Would normally go to a NGK but there...
Basically replacing the whole front of my 4.6 V8, so I've had a few questions lately. Thanks for all the help.
I just picked up a new thermostat. I've noticed when I pick it up it makes a rattling sound, like something may be loose inside it. Is this normal? My mechanic seems to think it...
Just putting together the front cover and oil pump. I've been told I have to prime the new oil pump. Some searching has mentioned cam lube or even petroleum jelly. A friend of mine recommended using some molly transmission aditive. Any advice on the best approach to priming a new oil pump in...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.