Search results

Happy this all worked out and I got to meet yet another great Rover person. Hope you enjoy the truck as much as I did. AndrewT

Sale pending.

Thx for the nice comments. I uploaded more pics to account and can be seen at link below. Also updated as ODO is at 81K and original listing stated 80K. No, I didn't have time to wash it. It looks better this way anyway. Pelicans on roof and cargo carrier and ScanGauge on dash are not...

SOLD! Donation sent to Dweb as well. AndrewT

PM'd you on both front seats. AndrewT

Check your tach and MIL lamp when you crank it. If the tach doesn't move at all and the MIL remains lit, you likely have a bad CKP sensor. I think they are like $70 or so if you end up needing one. The RAVE CD says you need to use Testbook to reset the new sensor with stored data as baseline...

Maybe you tripped the inertia switch? I know that kills the fuel pump. I think the only other sensor that can prevent you from starting is a bad CKP (crankshaft positioning) sensor. Maybe you accidentally dis-lodged the wiring there. When you put the key in the on position, do you hear the...

Also - if you end up replacing the motor, I would go ahead and replace those crappy solenoids as well. Mine kept going after being used once or twice. Not sure why. I ended up with an Albright sealed solenoid pack and this has worked great. You can get it from Summit though they do not...

When you did the test did you completely disconnect the solenoid wiring? You need to remove all solenoid wiring to the winch to perform the test Ryan listed which does work for the X9 winch motor. And make sure the battery ground is still connected to the winch ground. I completely rebuilt my...

Pin 2 powers the light on the switch.

This is cut and paste from an earlier post of mine on the same question. Do a search here and you will find lots of info on wiring OEM binnacle switches. Best to search using 'binnacle'. I have a note below on how you get them to come on with high-beam instead of low-beam. The relay basically...

Bump for a nice truck. Whether you like Gem or not, its a well built Disco for sure. Someone once told me that character is not determined by how much shit someone has to deal with, but in the manner by which they deal with the shit. Maybe that applies here as well - maybe not. Gem - I wish...

Talked to him this AM. He is around.

Yes to both questions.

NAPA or any parts store (even Lowes/HD) have the plastic conduit. The difference in the light switches is only cosmetic = color. $15 one is grey and not really black so if you have a later model yr it may not match 100% as those binnacle switches are all black. I put the $15 one on my 2004...

That is true. I welded up the crush-cans on my ARB and no issues winching so far. Its a very easy fix. Note I didn't weld the cans to the frame - I just welded support across the accordion-section of the can so it cannot deform/bend. I guess I lost my 5mph bumper rating with that one. AndrewT

The screw on the rotor is a #4 pozi-drive. Or use the biggest philips bit you have. I am sure opinions vary on rotors. I haven't heard much bad about DBA - thats what I'm buying. I'd avoid the parts store 'generic' stuff. You likely need to bleed all 4 brakes if you drove it until they were...

Thx - Good to know. Learn something new every day. AndrewT

Test 3,4,5 wires with in-line test light to see if you are getting good spark to the plug. If not, move your way backwards to find the issue. I would not rely on any multimeter readings on the wires as those are HT leads and operate differently from 'normal' voltage wiring. I personally have...

Try emailing them. I left vmails and no reply then emailed and got a response within an hour. AndrewT