Search results

SOLD! Donation sent to Dweb as well. AndrewT

1999 Disco. Not mine - helping a friend. Have the rear seat back off and have the ratcheting mechanism free of the seat. It retracts in but will not pull out. I have the assembly partially apart but not sure how to completely dis-assemble and/or if this is even fixable. Seems to be a...

37K miles. Had the SES light come on. Blinked then steady at idle. Blinks if you rev it above 1500 RPM or while driving so keeps throwing the codes. OBD scan shows 0300, 0305, 0308 (misfire). So I figured some issue on #5 or #8. Here is what I've done: Checked #5 and 8 plugs and wires...

For Spare. Needs to have some life left on it - but not much. AndrewT

This may be a dumb question but better safe than sorry. My first winch (used) Superwinch X9. Came with brand new MasterPull synth line. See pic. Need to figure out best way to secure line to the drum. The stock mounting holes and set screw on the drum will not work with the eyelet on the...

Couldn't find this in the TSB section here. Online searches seem to be for pay sites to access the info. TEC8616973 NOV 97 ECU/ECM - Intermittent No Crank/No Start. Chris - you got this one? Did I miss this in the TSB section? TIA, AndrewT

There is apparently a resistor between the coil and the ECU on my friend's '95 D1. Only his rig doesn't have one and I think this may be his firing issues. Anyone have a PN for this and/or know what size this is and whether or not the absence of this would cause starting issues? I checked the...

Quick question. I hooked up my CB and I get a noticeable hum on it when the car is running. Sounds fine and quiet when the car is not running - the loudish hum only starts with the engine running but does not vary as the car is rev'd. I switched antenna coax and it doesn't matter - same...

I have a set of 5 aluminum wheel adaptors (1 1/4" thick) that let you run older style D1/P38/D90 rims on the newer D2 bolt pattern. These were custom made for me by Stockton Wheels in Cali (very reputable wheel shop) and are new (not used). Also includes lug nuts for the adaptors. You supply...

I'm working on a friend's rig and the brake hard lines going from the front to the rear axle are toast (split and leaking). I see replacement line sets for sale on AB and elsewhere and I can also fab up some with 3/16" tubing, bender and a flaring kit. Question is, can these be pre-built and...

I have a portable CB (Cobra 38 WX ST) that I want to mount when using in the truck to keep it from bouncing around. I also have an external antenna I will hook up for in-cab use. Does RAM or someone make a mount for these type of portable units? Its got a belt clip on it so I assume I could...

Searched here and didn't see alot of info. Inquiring on options for mounting an external antenna for my newly purchased (used) Garmin 276C unit. What are the best mount locations on a D2? I was thinking on the ARB somewhere but thats getting increasingly dirty now-a-days. Plus someone here...

Anyone know what this is? Need th size of the 109 lug nut including pitch. AndrewT

Ok - did some searching but confused by results so here goes: Can I run early model rover rims on my '04 DiscoII with a spacer? I saw some site that sells some type of spacer but wanted to confirm the application. I know the bolt pattern is different so I am hoping there is something...

I've heard people trim the lower flange/edge of the ARB bumper to help approach angle. I am about to take the bumper off to install an X9 winch and to do some other work down there and was considering getting this done at the same time. Did a search here and didn't find much. I recall it...

OK - last week my PS low-beam light went out. Go to dealer as I read here they are warranty items. They replaced all 4 bulbs or so they say. I asked why it took them almost 90 mins to simply replace one bulb and they said they did all 4 as they have had issues with the bulbs. No fee and all...

Coffee mug. Fawkers. They give me a free LRover stainless steel travel coffee mug when I bought my Rover last April. Been using it and noticed wet area in the cup holder. Didn't think much of it. Filled it up this AM and hear this hissing sound with coffee slowly leaking out the bottom...

Opinons pls. Gonna pull the trigger on 2 1610s or 2 iM2720s. Both seem similar and about same size. I've never had either but plan to use them for on-rack storage, camping, air travel w/gear, etc... All other crap I've bought before wears out or leaks. Time to try the good stuff now...

On my '04 Disco S. I had planned to route rack light wiring through the headliner and factory roof rail as others have done. It looks the cleanest and best but also alot of work and I don't want to be removing all those plastic rivets in this cold as they are sure to break. However, in...

'04 Disco S. I wired up new factory switches for fog and Aux lighting. Came out nice. I did this all with the binnacle in-place - but I had to push the OEM wiring not being used behind the binnacle and now things are realy tight in there (a few wires keep pushing out by the instrument...