Search results

2018 Land Rover Discovery 4.0 LE (2018-11-18 16:50:05)

I have seen that people have replaced their D1 transmission cooler with a P38 transmission cooler. I want to keep the lines stock as adding custom lines isn?t a bad idea but i would imagining ordering stock lines in the future would be faster if neeed. Once the standard cooler was removed...

My 1998 disco has semi-retired from road use. I drive it on a farm, ground sometimes exhibits deep mud. I'd also like to be able to clear the brush in my woods and drive through there without getting a twig in my tire. The only time the rover will see the road is if roads get too snowy for my...

I had a problem with cat and evap readiness test not being ready. Then I took it for it's drive cycle. Sure enough the Evap, became ready, cat did not. There are no pending codes and no perm codes, no codes at all. When I use my tester to query the non-continuous tests under mode 6, one...

I am installing a Prodigy 3 brake controller on my 1998 Disco I. Is there a good way to run 10 guage wire back to the RH rear light assembly where the orginal trailer wiring is? I already have the 7 pin connected up for lights, just need to add brake control. Thanks very much!

I was just wondering if anyone knows if there is a GM part cross reference for a long front cv joint? 1998 disco I US spec Thanks very much! James

I was just wondering if anyone knows if there is a GM part cross reference for a long front cv joint? 1998 disco I US spec Thanks very much! James

Hello chaps! Could one of you possibly help me out with the size of serp belt I need for my 1998 D1. I ordered the Mean Green Alternator today and would like to get prepared for it's arrival. Thanks very much! James PS I did troll through the boards to see if I could answer my own question...

Okay so I take the coldest day in Indiana to move house. I get all my stuff in a uhaul trailer attached to the LR Disco I (98) all is well, until I try and park the trailer at the new house. Well the snow was disguising a ditch, so the LR and I end up in the ditch with the trailer attached. I...

I know this subject is a little flogged to death. I have just replaced my plugs and have found my HT leads to be in a state that I can only describe as "extra crispy"... Anyway, I wanted to cut my own MSD wires since I have nothing better to do. So now I am a little confused, I know I need...

Hello, I have a 1998 Disco I with 80k on the clock. There is this fan that used to drop out when I would get up to about 30 mph. I am assuming that this is the viscous fan. The fan speed seemed to be connected to engine speed until it disengaged or at least slowed down to the point that it...

What socket do I need to remove the oil drain plug on a D1?? Thanks

Ok I (finally) got the lug nuts off the first wheel, wheel comes off did half the brake job and put everything back. Moved on to wheel two, got all the nuts off. Now the wheel won't come off the hub, what is up with that? Please could someone help. Something I thought would take a couple of...

I need to replace the pads and discs on my disco I. I was wondering, what do you guys think as to which brand i should replace them with? Any experiences with EBC or DBA? James :)

I was going to buy some Magnecor ignition cables for my Disco I 1998. Is it the 7mm wires I need? If there is a brand better suited to the disco, could you also let me know that. James :)

What coolant (type and brand) do you think I should put in my D1? :)

How much brake fluid should I have for the 60k drain on a D1? I have everything else, just can't find this in the maint manual. Thanks, James

First off... The maint manual for my disco I says for auto transmission that I should use either Dexron III or Dexron IID, so I shall use Dexron III. However the powersteering seems to call for only Dexron IID, is there any reason for this? Can I just use more Dexron III? Next, does anyone...