Search results

Anyone have a good 4.0 or 4.6 Gems motor for sale?

Please send me a note or email to cjfinch@mac.com with price including shipping to 10509.

SOLD 12/10/11 A great vehicle at the right price for parts, project or continued restoration. Easily $8k in parts on the low end probably more. Photo's from June 4th 2004 - June 18th 2011: http://bit.ly/sa99LW Short list of parts upgraded, repaired or replaced include but are not limited to...

Please let me know if you have one, how much you want for it with shipping to NY 10509 and how you would like to receive payment.. Cheers, -Cj

Up for sale is this Brand New Black Teflon Coated Swivel Ball part number FTC 5105. Fits: 1989-98 Discovery 1 with ABS 1986-1994 Range Rover with ABS Defender up to and including VIN#KA930455 (1993 Model Year) I am in Brewster NY 10509 and am offering this part for $150 including shipping..

If I can't find the wiring diagram to troubleshoot the wires between my ECU and Coil Pack I may have to take the more expensive route and try swapping another ECU, does anyone have an ECU for my 97D1 available? How much with shipping to 10509?

So I threw these two codes, among many other things, and attempted to alleviate them by performing the following: Using a known spare coil pack I swapped coil #1 of 4, drove for a while and threw the same codes.. I then swapped coil #4 of 4 drove for a while and am throwing the same codes...

Seeking some advice and opinion.. If you were going to rebuild your front axle (in two different projects and time intervals entirely due to potential cost), and you were starting with the front right or passenger side of the vehicle because there is internal mechanical failure (likely CV)...

Looking for a black teflon swivel or an entire front axle for a 97D1 with swivel's that are in phenomenal shape.. Would be interested in front axle with diff and 24 splines or one with locker if someone has one for sale too..

What tools should I have available to install a exhaust manifold in a D1? Is it necessary to replace all the gaskets and bolts? And is there anything I should be aware of or concerned about when performing such an installation or is it as straight forward as it appears? Thanks for your help, -Cj

I think its time to replace manifold(s) and wanted to field some opinions on whether or not to replace with stock headers from AB or RN or wherever or if these Hedman Headers (below) from D&D were better? $200.00 39800 Headers ? Hedman brand, 4 into 1, painted black, 1 ?? primary tubes...

Preferably new or very low mileage.. If you have them on axles and they are showing no leaks and want to send all in one piece that works for me.. Please contact me if you have some available or know someone who does. Thanks!

I am looking for a low mileage transfer case out of an early model D2 to install in my 97D1. Please contact me if you know someone of have one available. Thanks!

I am in need of a new alternator for my 97 D1 4.6. I appreciate any recomendations on a quality dealer, rebuilder or person to buy a new alternator from. A quality part is my greatest concern, a good price is my next. Thanks for the help!

So the cops have busted my balsl twice about this and I have tried numerous times to fix.. Its the tailight on the drivers side and its a brake light issue.. This brake like is dimmer then the one on the right. I have swapped bulbs and those plastic things that hold them in and same issues...

Hi All, Could use some help pinpointing some noise undeneath my D1, it really sounds like something is going to fall off and I can't figure out what it is!!! The noise was there before I replaced the 4.0 with a 4.6. It was also there before I replaced all the bearings, cv joints, stubs in the...

Does anyone know if the D2 front seats fit in a D1? On the D1 frames?

Anyone know where to get some Diamond Plate Rocker Panels for a D1 or do I need to have them custom made?

Wanted: 4.6 Gems Plenum Cover..

used - good shape - make offer..