Search results

Truck :: 2007 Land Rover Range Rover HSE (2018-09-08 21:35:41)

I don't name my vehicles :: 1988 Land Rover Range Rover Classic (2018-02-09 17:39:01)

I don't name my vehicles :: 2002 Land Rover Disco 2 (2018-02-09 17:37:52)

I searched, but could not find what I was looking for. I recently changed the front output housing on my '02 D2 in order to have a locking case. Recently, it has started to have a harsh clunk under deceleration, almost like the case is slipping into, or attempting to slip into neutral. I'm...

I'm sure this has been covered, but I cannot find any info: will the front nose of an LT230Q fit into the t-case on an '02 Disco as is? If not, what all do I need to change out? I have the '02 front nose separated from the case, but I haven't completely removed it yet. Mike

If anyone has a new or used one, please let me know. Thanks in advance! Mike

So, went out for a roughly 9 hour round trip today. About 3 hours into the trip, the truck has a harsh "klunk." I didn't think much of it as I was running up and down some steep hills, and just assumed that the transmission had a moment of stupidity. About 30 minutes later, it happens again...

I have been a member on here for a long time; lost my first D2 in an accident, went to an LR4, got away from Rovers for a bit, but finally picking up another D2. That said, I am getting the truck from a friend (I inspected it for him when before he bought it 2 years ago), it is a clean truck...

Since we don't have an LR4 section yet, I guess I'll pose the question here. I've had my LR4 for a year now, and unfortunately, the Pirrelli Scorpions that came on the truck are already crapping out on me. For those of you that have an LR4, or LR3 for that matter, what tires have you found...

Since we don't have an LR4 section yet, I guess I'll pose the question here. I've had my LR4 for a year now, and unfortunately, the Pirrelli Scorpions that came on the truck are already crapping out on me. For those of you that have an LR4, or LR3 for that matter, what tires have you found...

After rolling my Disco six times a couple of years ago, I've finally got my ass back in a Rover. It's a 2011 LR4 Metropolis Edition. Mike

I'm upgrading the entire stereo in my 00 D2, to include wiring and all. I searched but could not find any wiring diagram for hard wiring the head unit into the truck. I'm planning on hardwiring the head unit because I read that that was the best way to go at it. I will admit that I have very...

So here's the deal: I had surgery on the 25th of Feb. In the mail today I received a letter from a supposed 'surgical assistant' claiming I owed $200 for services rendered during my surgery. The letter arrived in an envelope that looked like my Grandma had sent it. I started to get...

My D2 threw a P0741- Torque converter clutch performance or stuck off code today. I did some searching on here, but I didn't really find out to much. Someone was saying to change the tranny fluid and filter and than clear the code. Well, I just changed all the fluids about 1,000 or so miles...

Alright, I know, I know, search; I did. Here's the issue. My 00 D2 is making a weird squeak, not the normal chirp associated with a bad u-joint (it only does it intermittently). I had the truck on a frame lift today to put a new abs sensor on the left rear wheel and while I was under the...

Anyone know if there is any good wheeling spots near the Columbus, GA area? Mike

This question may have been answered already, but I could not find the answer. So, is it possible to do a Toyato axle conversion on D2 axles or can it only be done on D1 axles? Mike

So, I finally was able to take my Disco out for its first run after the new lift. Everything started out fine and than all off a sudden I get a huge metallic POP, like the exact sound an axle shaft makes when it snaps; however, nothing happened, not one single broken part. The truck continued...

So the time had finally come for me to change my lower ball joint on the front of the D2. WOW, what a pain in the fucking ass. For those of you who have to do it here are a few suggestions: 1. Use lots of heat. A torch is your friend. Get the inner knuckle or whatever it is called red hot...

I'm a big speed metal fan and I thought someone would appreciate this. Michael Angelo Batio is a FREAK!! http://www.youtube.com/watch?v=hb5QaCfm7bg