I am selling these covers to a set of Hella 500 (6-3/8 inch) Driving or Fog lights.
The white covers are the factory supplied, but the clear are Hella add-on covers for constant rock protection.
Email or call David at: 720.940.6354.
I am selling two (2) Firestik CB (Citizens Band) antennas.
Four (4) foot Firestik Firefly - black
The "FL" Series antennas are the performance leader of lightweight top-loaded CB antennas. Each is approximately 40% lighter than the equivalent length Firestik II antenna. From the perspective of...
YEAHHHH, the only door that was not compressed closed was the front passenger side. The truck is not recoverable... To quote the tow truck driver after he had dragged it about 10 feet on its side... "I think your tie rod is busted!" Yeah no shit sherlock, otherwise I would drive it home...
Thank you for all of your well wishes... For the Colorado guys, we had just run Coney Flats to Middle St. Vrain and had a great day.
Rounding a corner on the Peak to Peak Highway just north of Ward Colorado I caught a sun glare with no sunglasses on and by the time I got the visor down my...
2000 DII - CDL - 245/75/16
I have a slight bend in some body panels that I can not explain. Is this a common occurence among DIIs?
- - - - - - - - - - - - - -
On the way home from a GREAT trail run today I found a nice soft shoulder on one of our Colorado two-lane highways...
Three - ABS, ETC, Downhill Decent.
You ABS faults out whether it be an actual failure of an ABS sensor or just a dirt or even a bad brake sqeak can cause a fault on the ABS sensor (probably the weakest link on the Disco).
Basically, your Traction Control (ETC) and Downhill Descent Control...
Scott, I do have a 2000 and the Latch is not in mine! I believe that they were installed in the 2001, but would need to hear from the 01 owners out there. Our 03 definately has them.
Where have you guys put your CB unit in your Disco? I spent an hour tonight trying to find just the right place and haven't yet found it.
Pics would really help!
I do like the OEM light bar, but I will take $12 in parts and 1.5 hours of labor over $150+ of my hard duckets any day. The OEM bar is stronger and more ridgid, but did I mention $12?
Finishsed Product
I finished the fabircation yesterday and the priming, painting, and install today. Took a midnight run around the neighborhood with my lights on and off to test and stop and adjust. Good thing I am on the HOA Board...!
Check out the finished pics...
Check out: http://discoweb.org/tire.htm
285/75-16 would fit, but you might have to trim a little and gearing could become an issue. If you are just looking for more grip, then go a little wider, but not taller.
Check out: http://www.miata.net/garage/tirecalc.html for exact tire size comparisons.
On the jam nuts... I did use an adjustable crescent wrench on one side and a vis grip on the other. I don't remember having an issue with that nut. All i can say is do you best and take the opportunity to go buy some new tools.
On the bolts... I have no idea!
So, would it be wiser to use steel angle rather than aluminium? I probably just would not be doing as much cutting and bending on the ends.
Isn't the sub-bumper aluminium or is it steel?
Would using the less hardened zinc bolts and nuts solve the problem?
OK, So the sub bumper behind the plastic, I assume is aluminium, right? The angle that I am planning on using is aluminium, but I was planning on using stainless nuts and bolts. QUESTION: so it is not a power / ground issue, but a steel on aluminium issue? Causes which to do what?
Assume that...
I know D2Offrover. His light bar is from Rover's North... $150. I thought if I could build something for much less, than I would go that route.
Yes, I thought I would go with Bolts instead of screws. Just didn't update my schematic.
On isolating the screws, I see lights bolted to brush...
I have a concept for a light bar for the front of my 00 DII, but I wanted to see if any of you have fabbed one and if you had any pictures.
I don't think my idea is the only one out there, but the best that I could think of.
Please post up with any other ideas.
Any suggestions to my design...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.