Search results

Looking for a left front (US Driver) aluminum door threshold. The piece that screws to the floor between the door seal and carpet.

Looking for the grey plastic dash bezel. The dash piece that holds the heater vents and clock.

I'm looking for a set of 93/94 long wheelbase Range Rover Classic seats. Depending on the color I need either just the fronts or the fronts and rear seats. Looking for a set in very very good condition. I'm fine with replacing motors and fixing switches, but the seat frame, leather, etc needs...

Completely rebuilt 3.9l V8 short block + heads + extras $2700 Located in Mount Vernon, WA Never run. Stored in my workshop in plastic bags since the rebuild. The 3.9L block and heads came out of a 1995 discovery which was an interim year between the the v-belt 3.9l and 4.0l variants. It has...

I just finished replacing the main wiring harness in my truck and I'm down to just 2 wires that I can't find a home for. The first is near the e-brake and the second is near the shifter. I can't for the life of me remember what I pulled them off of, and can't see a matching connector for...

I have a damaged dash wiring harness, bought a used one in good shape, and am getting ready to swap it. As far as I can tell, this is just a time consuming dissasemble, re-assemble project. I don't have to worry about dust getting into anything, don't have to worry about torque values, etc...

I'm attempting to rebuild my 7100 following the Bilstein rebuild guide. Everything was going fine until I tried to refill them with oil. The instructions appear to be innacurrate including the example. - As I understand it, the rebuild guide states that I should put in 700ml total on a 10"...

NOTE: FREE SHIPPING IS NO LONGER AVAILABLE -- this post was originally made in June of 2009. Overland Navigator turns any Windows netbook, laptop, tablet, or UMPC and a cheap GPS puck into an easy to use offroad mapping system. USGS topographic maps are rich in detail. Maps are seamless...

Why do some DIIs have an extra wide driver side interior panel in the cargo area? For example in this photo the jump seat is over about 4-5" compared to my 99 7 seater.

Navigation System In the past I had a "carputer" that did everything (AM/FM/CD/NAV/MP3/DivX/DVD etc). The trouble with this setup was that I was always worried about it if I left the truck at a hiking trailhead. I like having a PC in the car though, as I can use it for Nav, as an OBDII...

The D2s have a portion of the housing that is made out of plastic, and this plastic likes to crack. I replaced my radiator with another genuine radiator a little over a year ago, and this one cracked too. Are there any reasonably priced aftermarket radiator options for the D2?

99 D2 w/ 4.6l shortblock and 4.0 ECU/top end. I back down a hill on the trail yesterday, stop, put the truck in drive and it stalls. I make a joke over the radio about how I'd never heard of anyone killing an engine while shifting an automatic. Restart and and the CES light is on so I pull...

I'm looking for several DII interior pieces in grey. - Steering wheel - Drivers side footwell kick panel. The one on the lower left where the left foot can rest. - Driver rear cubby/jump seat panel. Don't care which as long as it is in Grey. This is the big piece that goes from the rear cargo...

I'm looking for several DII interior pieces in grey. - Steering wheel - Drivers side footwell kick panel. The one on the lower left where the left foot can rest. - Driver rear cubby/jump seat panel. Don't care which as long as it is in Grey. This is the big piece that goes from the rear...

My new set of pads are a bit odd. 2 of them have directional arrows and a small opening in the backing plate that is possibly a vent. There are no instructions that indicate which of the pads goes against the caliper piston (inside) and which pads fit on the caliper retaining bracket...

Land Rover has a big old warning on the visor of the DII indicating that the air bags need to be replaced after 10 years. I just overheard someone requesting a quote on this and they were quoted $3700. WTF? At that price, I'll be unplugging a couple of wires and possibly removing a few ECUs...

Anyone know of a CO2 tank that mounts on its side so the regulator comes out the top when mounted on its side? I'm looking to replace this OBA setup with CO2 but keep the plumbing and drawer setup the same. Thanks!

Two weekends ago my son and I headed into the Cascade Mountains to scout out a trail for an upcoming Perseids Meteor shower club trail run/campout. Other than breaking my rear diff on a hill climb it was a good trip. A few additional photos can be found at...

I have a complete rear output housing for my LT230SE w/ good bearings/seals that I am going to swap in tomorrow. In the photo below (For a Defender LT230T) item number 2 in the attached drawing is a gasket. My DII Workshop Manual makes no mention of this gasket and only mentions Hylosil 102...

It's been a while since I've looked around. Are there any options other than GBR / Maxi-drive HD rear axles for the the DII? Rovertracks doesn't make anything.