Search results

Hi guys, Been a while. Anyway my Dad changed my brakes for me but he is saying he that he has to cycle the brake peddle once before the brakes actually become effective. I tend to think its a bleeding issue but he says he suspects the master cyl. What do you all think? I haven't seen the...

double post... My bad...

I have a buddy with a 2000 RR and he takes it to the stealership. I suggested an indy shop but dont really know of any in the area, since I havent lived here for over 2 years now. I'd work on it myself but I'm headed to korea on friday. Do you all have a direction I could point him in...

I'm going to be headed to Korea for a year on 1 Feb and my dad will be babysitting rover while I am gone. Are there any indy shops (preferably Aurora area) that you would recommend for him to use should something fail? I think I have just about everything lined out but Murphy's law of rovers...

Anyone read Under the Banner of Heaven? I'm just under half way through it. Pretty interesting book so far... Got polygamy?? JMK

I few weeks ago I wrote about having hard start/fuel pressure issuse (it also idled high with a code 48 thrown.) Now I am getting it again. It still idles high on start sometimes as much as 1800 ish and others like 1500ish. Now what? Code 48 is the base idle code. It also points at the speed...

I have a '94 with the 3.9L. There are a few issues I have with it right now. The first is that I have low fuel pressure (about 30psi at idle) and it drops to 0 on shut down. It bleeds down in the time it takes me to kill her and to get back to the gauge. The book tells me to R2 the pressure...

http://www.pangaea-expeditions.com/tech/obdcodes.html#45 I had no clue there was a fault code display in the the rover. Maybe this will help someone. JMK

So I am going to Hill AFB by way of korea. Is it as cool there as I have heard? Much local off roading to be had? Thanks! JMK

For those of you who have a on board air sys Where do you hide the air tank? Since I am using the AC for a pump I am thinking about doing away with the rear blower and placing it there. It wont fit between the frame rails that I can see. Any other suggestions? Thanks as always. JMK

I am having a bit of a x-fer case leak on my 94 d1. I looked at it and it appears that the leak is coming from the fwd housing joint face. Is this something that can be resealed in place? I am thinking not but for the sake of lazyness and compleat lack of motivation I have to ask. I am getting...

Im going to be down in So cal next month and I want to do some off roading while I am there. Whats everyones favorite trails in the big bear area? JMK

Many people using rovertracks front half shafts? I was thinking about getting a set. Whats everyone think of them? I know the abs doesnt work with them. thanks. JMK

Im looking for off road trails in the north centralish part of NM. Anybody know of any good ones? JMK

I just installed a RTE 3" lift on my 94 rover. Its a bit higher in the front than the back by 2 or so inches. My question is did I fuck up somewhere or did RTE? Or maybe they are assuming that I have a bumper and winch. Not sure. What do you all think? Not real high on the pre-runner look...

I just put a RTE 3" lift on my '94 Disco 1 and its pretty much B.A. My question is what drive shafts are the prefered? Tom Woods, GB, or that kit Atlantic british and rovers north sell? Thanks as always. JMK

Whats the advantage of relocating the steering dampener? Also I am planing to put a 3" lift on my '94 disco I. On the rovertym site they sat that drive shafts arnt included and thats fine, but where would I go to get them? Thanks as always. JMK

I have read that a few people have them. Where do you get them? I have never seen them for rovers. Thanks JMK

Has anyone done this? I know of a few jeep people who have and has worked very well. Well enough to run air tools off it for 30 min or more. Anyway just looking for projects, not that I dont have enough all ready... lol Thanks. JMK

Anyone ever heard of a short in the O2 sensor wiring causing the fuel pump fuse to burn out? I had put up a few posts about the fuse bit. I am pretty sure it has been fixed. atleast til I get back from the sand box. Anyway the wire burned out on the exaust manifold. Thanks as always. JMK